This section helps you set up your ConnectCore device to see LVGL in action.

The goal of this section is to have an LVGL demo application running in your device. The application is a slightly modified version of the LVGL Linux Framebuffer example, which runs the Widgets demo.

Follow these steps to get started using the LVGL demo with your ConnectCore 93 Development Kit.

Requirements

  • A ConnectCore 93 Development Kit

  • LVDS or HDMI display for the graphical user interface

  • A mouse to work in the graphical user interface

Download the firmware

Download the firmware images from the following location: https://ftp1.digi.com/support/digiembeddedyocto/5.0/r1/images/ccimx93-dvk/ccimx93-dvk-lvgl-installer.zip

Program the LVGL demo image

Digi recommends you program the images using the Universal Update Utility (UUU) through a USB connection to your development PC.

  1. Decompress the zip file in a directory of your choice.

  2. Download the latest Universal Update Utility (UUU), a software tool from NXP.

    UUU version should be v1.5.11 or higher.

  3. Place the uuu executable in a directory in your PATH, such as /usr/bin.

  4. Install udev rules to allow any user to run uuu to access the USB port:

    $ sudo sh -c "uuu -udev >> /etc/udev/rules.d/70-uuu.rules"
$ sudo udevadm control --reload

  5. Connect a USB type-C cable to your development PC and the other end to the target USB type-C connector.

  6. Reset the device by pressing the reset button on the board and immediately press any key in the serial terminal to stop the auto-boot process. The U-Boot bootloader prompt displays:

    U-Boot SPL dub-2024.04-r2.2+g9218b07cddd+p0 (Feb 24 2025 - 15:03:54 +0000)
SOC: 0xa1009300
LC: 0x2040010
PMIC: PCA9451A
PMIC: Over Drive Voltage Mode
M33 prepare ok
Normal Boot
Trying to boot from BOOTROM
Boot Stage: Primary boot
image offset 0x0, pagesize 0x200, ivt offset 0x0
Load image from 0x52800 by ROM_API
NOTICE:  TRDC init done
NOTICE:  BL31: v2.10.0  (release):android-15.0.0_1.0.0-rc3-0-g1b27ee3ed-dirty
NOTICE:  BL31: Built : 15:03:54, Feb 24 2025

U-Boot dub-2024.04-r2.2+g9218b07cddd+p0 (Feb 24 2025 - 15:03:54 +0000)
Reset Status: POR
CPU:   NXP i.MX93(52) Rev1.1 A55 at 1700 MHz
CPU:   Industrial temperature grade  (-40C to 105C) at 40C
DRAM:  992 MiB
Core:  221 devices, 34 uclasses, devicetree: separate
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
[*]-Video Link 0 (1920 x 1080)
       [0] lcd-controller@4ae30000, video
       [1] dsi@4ae10000, video_bridge
       [2] lt8912@48, panel
In:    serial
Out:   serial
Err:   serial
Model: Digi ConnectCore 93 Development Kit
ConnectCore 93 SOM variant 0x01: 992 MiB LPDDR4, Wi-Fi, Bluetooth
 Board version undefined, ID undefined
Boot:  MMC0
BuildInfo:
 - ELE firmware version 2.0.0-64d8ef47
flash target is MMC:0
Net:   eth0: ethernet@428a0000 [PRIME]
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
=>
    Information in the console log may vary.

  7. On the target, in U-Boot, execute the following command:

    => fastboot 0

  8. On your development PC, change to the directory where you extracted the ZIP file:

    $ cd <zip-folder>

  9. To program the demo image, run:

    $ ./install_linux_fw_uuu.sh -i dey-image-lvgl

  10. Once the firmware is installed, the device boots automatically. The default username is root with no password.

Test the LVGL demo

The LVGL demo is automatically launched on boot.

LVGL widgets demo
The application’s scrolling mechanism works as if you’re using a touchscreen, even when you’re using a mouse. To scroll in a specific direction, click and hold anywhere in the application window and move the mouse in the opposite direction while holding the mouse button.

To build an image with a customized version of the demo, see Customize the LVGL demo.