The prebuilt ConnectCore WebKit image includes the ConnectCore demo.

  1. Establish a serial connection with your device

  2. Download the firmware

  3. Program the firmware

1. Establish a serial connection with your device

Open a serial connection with the device. You can use any serial terminal program such as Tera Term, Minicom, CoolTerm, or HyperTerminal.

PuTTY terminal program is not recommended due to an incompatibility with the USB/serial driver.

Open a serial connection with the following settings:

Parameter Value

Port

Serial port where the device is connected

Baud rate

115200

Data bits

8

Parity

None

Stop bits

1

Flow control

None

2. Download the firmware

To access firmware images, please fill out the following form to provide some information so we can better understand your project needs.

If the form doesn’t load after a few seconds, you may need to refresh the page. Contact Digi Support Services if you are not able to access the firmware images.

3. Program the firmware

Digi recommends you Use the Universal Update Utility (UUU) through a USB connection to your development PC to program the images.

  1. Decompress the zip file in a directory of your choice.

  2. Download the latest Universal Update Utility (UUU) tool, a software tool from NXP.

  3. Place the uuu executable in a directory in your PATH, such as /usr/bin.

  4. Install udev rules to allow any user to run the uuu for accessing the USB port:

    $ sudo sh -c "uuu -udev >> /etc/udev/rules.d/99-uuu.rules"
$ sudo udevadm control --reload-rules

  5. Connect a USB type-C cable to your development PC and the other end to the target USB type-C connector.

  6. Reset the device by pressing the reset button on the board and immediately press any key in the serial terminal to stop the auto-boot process. The U-Boot bootloader prompt displays:

    U-Boot dub-2020.04-r2.2 (Jan 18 2021 - 15:54:04 +0000)

CPU:   NXP i.MX8QXP RevB A35 at 1200 MHz at 25C
DRAM:  2 GiB
MCA:   HW_VER=1  FW_VER=1.01
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Model: Digi International ConnectCore 8X SBC Pro Board.
ConnectCore 8X SOM variant 0x02: 2 GiB LPDDR4, Wi-Fi, Bluetooth, MCA, Crypto-auth
  Board version 3, ID 135
Boot:  MMC0

 BuildInfo:
  - SCFW 56682d58, SECO-FW 0e4b9cee, IMX-MKIMAGE 8da5cd23, ATF c949a88
  - U-Boot dub-2020.04-r2.2

flash target is MMC:0
Net:   eth0: ethernet@5b040000 [PRIME], eth1: ethernet@5b050000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
=>
    Information in the console log may vary.

  7. On the target, in U-Boot, execute the following command:

    => fastboot 1

  8. On your development PC, change to the directory where you extracted the ZIP file:

    $ cd <zip-folder>

  9. To program the WebKit image, run:

    $ ./install_linux_fw_uuu.sh -i dey-image-webkit

  10. Once the firmware is installed, the device boots automatically. The default username is root with no password.

While the recommended boot method is eMMC, you can also boot the WebKit kit image from a microSD card using the *.sdcard image file on the downloaded ZIP file. See Boot from microSD card for instructions on programming a microSD card and booting from it.

You must use a microSD with a minimum capacity of 8 GB.