The ConnectCore 6UL is shipped without a default operating system loaded. Only U-Boot is flashed in the device. This step demonstrates how to install Yocto in your ConnectCore 6UL.

1. Establish a serial connection with your device

Before you start programming the firmware, you must open a serial connection with the device. You can use any serial terminal program such as Tera Term, Minicom, CoolTerm, or HyperTerminal.

Due to an incompatibility between the USB/serial driver and the PuTTY terminal program, you must use another serial terminal program such as Tera Term, Minicom, CoolTerm, or HyperTerminal.

Open a serial connection with the following settings:

Parameter Value

Port

Serial port where the device is connected

Baud rate

115200

Data bits

8

Parity

None

Stop bits

1

Flow control

None

2. Program the firmware

Once you have established the serial connection, you can start the firmware update process. Follow these steps to install Yocto in the device:

  1. Download the firmware images from the following location:

  2. Decompress the zip file.

  3. Place the decompressed files in the root of a FAT-formatted microSD card and insert it in the microSD socket of the board.

  4. Reset the device by pressing the reset button on the board and immediately press any key in the serial terminal to stop the auto-boot process. The U-Boot bootloader prompt displays:

    U-Boot dub-2020.04-r2.2 (Jan 18 2021 - 15:58:10 +0000)

CPU:   i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 32C
Reset cause: POR
I2C:   ready
DRAM:  256 MiB
MCA:   HW_VER=1  FW_VER=1.19
PMIC:  PFUZE3000 DEV_ID=0x30 REV_ID=0x11
NAND:  256 MiB
MMC:   FSL_SDHC: 0
In:    serial
Out:   serial
Err:   serial
Model: Digi International ConnectCore 6UL SBC.
ConnectCore 6UL SOM variant 0x06: Industrial Ultralite 528MHz, 256MB NAND, 256MB DDR3, -40/+85C, Wireless, Bluetooth
  Board version 3, ID 135
Boot device:  NAND
Net:   FEC0 [PRIME]
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
{pu}
    Information in the console log may vary.

  5. Install the firmware into the internal NAND, executing the following command:

    => run install_linux_fw_sd

  6. Once the firmware is installed, the device boots automatically. The default username is root with no password.

During installation, error messages appear when the installation process attempts to override MAC addresses. These messages are expected.

## Resetting to default environment
oldval: 00:40:9D:7D:17:9A  defval: 00:04:f3:ff:ff:fa
## Error: Can't overwrite "ethaddr"
himport_r: can't insert "ethaddr=00:04:f3:ff:ff:fa" into hash table
oldval: 00:40:9D:7D:17:9B  defval: 00:04:f3:ff:ff:fb
## Error: Can't overwrite "eth1addr"
himport_r: can't insert "eth1addr=00:04:f3:ff:ff:fb" into hash table
oldval: 00:40:9D:7D:17:9C  defval: 00:04:f3:ff:ff:fc
## Error: Can't overwrite "wlanaddr"
himport_r: can't insert "wlanaddr=00:04:f3:ff:ff:fc" into hash table
oldval: 00:40:9D:7D:17:9D  defval: 00:04:f3:ff:ff:fd
## Error: Can't overwrite "btaddr"
himport_r: can't insert "btaddr=00:04:f3:ff:ff:fd" into hash table