Fastboot is a protocol for communication between your device and a computer. It allows you to modify file system images over a USB connection, which is a quick way to update firmware during development. Fastboot requires the USB interface to work as 'device'.

Although it was originally developed for Android images, its implementation on the NXP UUU (Universal Update Utility) tool extends the functionality to any file type.

To update U-Boot via USB OTG using uuu and the Fastboot protocol:

  1. Download the latest Universal Update Utility (UUU), a software tool from NXP.

    UUU version should be v1.5.11 or higher.

  2. Place the uuu executable in a directory in your PATH, such as /usr/bin.

  3. Install udev rules to allow any user to run uuu to access the USB port:

    $ sudo sh -c "uuu -udev >> /etc/udev/rules.d/70-uuu.rules"
$ sudo udevadm control --reload

  4. Connect a USB type-C cable to your development PC and the other end to the target USB type-C connector.

  5. Reset the device by pressing the reset button on the board and immediately press any key in the serial terminal to stop the auto-boot process. The U-Boot bootloader prompt displays:

    U-Boot SPL dub-2024.04-r2.2+g9218b07cddd+p0 (Feb 24 2025 - 15:03:54 +0000)
Normal Boot
Trying to boot from MMC1
Primary set selected
Load image from MMC/SD 0x5f400


U-Boot dub-2024.04-r2.2+g9218b07cddd+p0 (Feb 24 2025 - 15:03:54 +0000)

CPU:   NXP i.MX8QXP RevB A35 at 1200 MHz at 43C
DRAM:  2 GiB
MCA:   HW_VER=1  FW_VER=1.00
Core:  257 devices, 27 uclasses, devicetree: separate
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Model: Digi International ConnectCore 8X SBC Pro Board.
ConnectCore 8X SOM variant 0x02: 2 GiB LPDDR4, Wi-Fi, Bluetooth, MCA
  Board version 2, ID 135
Boot:  MMC0
Reset cause: POR

 BuildInfo:
  - SCFW 83624b99, SECO-FW c9de51c0, IMX-MKIMAGE 71b8c18a, ATF 1b27ee3
  - U-Boot dub-2024.04-r2.2+g9218b07cddd+p0

flash target is MMC:0
Net:   eth0: ethernet@5b040000 [PRIME], eth1: ethernet@5b050000
Fastboot: Normal
Normal Boot
Hit any key to stop autoboot:  0
=>
    Information in the console log may vary.

  6. On the target, in U-Boot, execute the following command:

    => fastboot 1

  7. On your development PC, change to your Digi Embedded Yocto project’s deploy images folder:

    $ cd tmp/deploy/images/ccimx8x-sbc-pro/

  8. Run the install_linux_fw_uuu.sh script with -h parameter to check the syntax:

    $ ./install_linux_fw_uuu.sh -h
############################################################
#           Linux firmware install through USB OTG         #
############################################################
Usage: ./install_linux_fw_uuu.sh [options]

  Options:
   -b                     Activate bootcount mechanism (3 boot attempts).
   -d                     Install firmware on dualboot partitions (system A and system B).
                          (Implies -b).
   -h                     Show this help.
   -i <dey-image-name>    Image name that prefixes the image filenames, such as 'dey-image-qt',
                          'dey-image-webkit', 'core-image-base'...
                          Defaults to 'dey-image-qt' if not provided.
   -k <dek-filename>      Update includes dek file.
                          (implies -t)."
   -n                     No wait. Skips 10 seconds delay to stop script.
   -t                     Install TrustFence artifacts.
   -u <u-boot-filename>   U-Boot filename.
                          Auto-determined by variant if not provided.

  9. To program the default image files (dey-image-qt):

    $ ./install_linux_fw_uuu.sh

  10. Once the firmware is installed, the device boots automatically. The default username is root with no password.