The NXP i.MX6 CPU has:

  • five SPI ports on the Quad/Dual variants.

  • four SPI ports on the Solo/DualLite variants.

On the ConnectCore 6 system-on-module:

  • All SPI ports are available on the LGA pads (multiplexed with other functionality).

On the ConnectCore 6 SBC:

  • SPI1 is available through an expansion connector.

Kernel configuration

You can manage the SPI driver support through the kernel configuration option:

  • Freescale i.MX SPI controllers interface (CONFIG_SPI_IMX)

This option is enabled as built-in on the ConnectCore 6 SBC kernel configuration file.

Kernel driver

The SPI bus driver for the ConnectCore 6 is located at drivers/spi/spi-imx.c.

The Linux driver supports the SPI bus in master mode only, and using PIO mode.

Device tree bindings and customization

The i.MX6 SPI interface device tree binding is documented at Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt.

The SPI interfaces are defined in the i.MX6 CPU, ConnectCore 6, and ConnectCore 6 SBC device tree files.

Example: SPI1

Definition of the bus

Common ConnectCore 6 device tree
ecspi1: ecspi@02008000 {
	#address-cells = <1>;
	#size-cells = <0>;
	compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
	reg = <0x02008000 0x4000>;
	interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>;
	clocks = <&clks IMX6QDL_CLK_ECSPI1>,
		 <&clks IMX6QDL_CLK_ECSPI1>;
	clock-names = "ipg", "per";
	dmas = <&sdma 3 7 1>, <&sdma 4 7 2>;
	dma-names = "rx", "tx";
	status = "disabled";
};

IOMUX configuration

Common ConnectCore 6 device tree
ecspi1 {
	pinctrl_ecspi1: ecspi1 {
		fsl,pins = <
			MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
			MX6QDL_PAD_EIM_EB2__GPIO2_IO30  0x100b1
			MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1
			MX6QDL_PAD_EIM_CS0__GPIO2_IO23  0x100b1
		>;
	};
};

Bus enabling

ConnectCore 6 SBC device tree
&ecspi1 {
	fsl,spi-num-chipselects = <2>;
	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>,<&gpio4 10 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_ecspi1>;
	status = "okay";
};

SPI user space usage

The SPI bus cannot be accessed directly from user space. Instead, it is accessed via the SPI client drivers. However, a special sample client driver allows raw access to the SPI bus.

SPI device interface

The Linux kernel offers a sample client driver called spidev that gives you read and write data access to the SPI bus through the /dev interface:

You can find this driver under the kernel configuration option User mode SPI device driver support (CONFIG_SPI_SPIDEV).

On Digi Embedded Yocto, this driver is enabled as a loadable module. The default device tree includes the spidev node in the device tree as an SPI device hanging from your SPI bus:

&ecspi1 {
	fsl,spi-num-chipselects = <2>;
	cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>,<&gpio4 10 GPIO_ACTIVE_HIGH>;
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_ecspi1>;
	status = "okay";
	spidev@0 {
		compatible = "spidev";
		reg = <0>;
		spi-max-frequency = <4000000>;
		status = "okay";
	};
};

To use it, load the spidev module from user space:

# modprobe spidev
spidev spi0.0: buggy DT: spidev listed directly in DT
Note that spidev is not a real hardware SPI device but a detail of how Linux controls a device. The kernel will warn loudly when spidev will be loaded. For reference, see https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=956b200a846e324322f6211034c734c65a38e550.

Linux will create a device node in the form /dev/spidevX.Y device node where X corresponds to the SPI bus index, starting at zero, and Y corresponds to the SPI bus chip select, starting at zero. For example, the ConnectCore 6 SBC peripheral SPI1 bus would be accessed through device node /dev/spidev0.0.

SPI device test application

Build the package dey-examples-spidev in your Yocto project to install the test application spidev_test.

This spidev_test application is a simple utility used to test SPI functionality via the spidev device.

Syntax

To display the application’s syntax run:

spidev_test --help

Example

Short-circuit the MISO and MOSI lines of your SPI bus to create a loopback that allows the bus to receive the same data it is sending.

Run the application using your spidev node /dev/spidevX.Y, where X is the SPI bus index and Y is the SPI bus chip select, for example:

# spidev_test -D /dev/spidev0.0 -v
spi mode: 0x0
bits per word: 8
max speed: 500000 Hz (500 KHz)
TX | FF FF FF FF FF FF 40 00 00 00 00 95 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF F0 0D  | ......@....�..................�.
RX | FF FF FF FF FF FF 40 00 00 00 00 95 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF F0 0D  | ......@....�..................�.

You should receive the same data displayed in the preceding excerpt.