You can show SureLink status for all interfaces, or for an individual interface. You can also show Surelink status for ipsec tunnels and OpenVPN clients.
SureLink status is only available from the Admin CLI.
Command line
Show SureLink State
To show the current state of SureLink for the EX15 device, use the show surelink state command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- At the Admin CLI prompt, type:
> show surelink state Test on network.interface.wan.ipv6 with condition: one dns_configured (n); network.interface.wan.ipv6; -> update_routing_table ACTION ATTEMPTS STATUS restart_interface 00/01 [FAILED] update_routing_table 00/01 Test on network.interface.modem.ipv4 with condition: all dns_configured (n); network.interface.modem.ipv4; -> restart_interface ACTION ATTEMPTS STATUS update_routing_table 00/03 [ BUSY ] restart_interface 00/03 reset_modem 00/03 switch_sim 00/03 modem_power_cycle 00/03 restart_interface 00/03 >
Show SureLink status for all interfaces
To show the SureLink status all interfaces, use the show surelink interface all command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- At the Admin CLI prompt, type :
> show surelink interface all Interface Test Proto Last Response Status --------- ----------------------------- ----- ------------- ------- wan Interface is up IPv4 32 seconds Passing wan Interface's DNS servers (DNS) IPv4 28 seconds Passing lan Interface is up IPv4 21 seconds Passing lan Interface's DNS servers (DNS) IPv4 20 seconds Passing modem Interface is up IPv4 115 seconds Passing modem Interface's DNS servers (DNS) IPv4 114 seconds Passing >
- Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection menu. Type quit to disconnect from the device.
Show SureLink status for a specific interface
To show the SureLink status a specific interface, use the show surelink interface name name command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- Use the show surelink interface name name command to show the Surelink status of a specific interface, for example:
> show surelink interface name wan wan1 Surelink Status -------------------- IPv4 Status : Passing IPv6 Status : Failed Test Proto Last Response Status ----------------------------- ----- ------------- ------ Interface's DNS servers (DNS) IPv6 15 seconds Failed > - Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection menu. Type quit to disconnect from the device.
Show SureLink status for all IPsec tunnels
To show the SureLink status all IPsec tunnels, use the show surelink ipsec all command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- At the Admin CLI prompt, type :
> show surelink ipsec all IPsec Test Last Response Status ------ -------------------- ------------- ------------------ test 194.43.79.74 (Ping) 29 seconds Passed test 194.43.79.75 (Ping) 5 seconds Passed test1 194.43.79.74 (Ping) 21 seconds Failed test2 194.43.79.75 (Ping) 21 seconds Waiting for result >
- Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection menu. Type quit to disconnect from the device.
Show SureLink status for a specific IPsec tunnel
To show the SureLink status a specific IPsec tunnel, use the show surelink ipsec tunnel name command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- Use the show surelink ipsec tunnel name command to show the Surelink status of a specific tunnel, for example:
> show surelink ipsec tunnel test IPsec Test Last Response Status ------ -------------------- ------------- ------------------ test 194.43.79.74 (Ping) 29 seconds Passed test 194.43.79.75 (Ping) 5 seconds Passed >
- Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection menu. Type quit to disconnect from the device.
Show SureLink status for all OpenVPN clients
To show the SureLink status all OpenVPN clients, use the show surelink openvpn client all command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- At the Admin CLI prompt, type :
> show surelink openvpn all OpenVPN Client Test Last Response Status -------------- -------------------- ------------- ------------------ test_client1 194.43.79.74 (Ping) 29 seconds Passed test_client1 194.43.79.75 (Ping) 5 seconds Passed test_client2 194.43.79.74 (Ping) 21 seconds Failed test_client2 194.43.79.75 (Ping) 21 seconds Waiting for result >
- Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection menu. Type quit to disconnect from the device.
Show SureLink status for a specific OpenVPN client
To show the SureLink status a specific OpenVPN client, use the show surelink openvpn client name command:
- Select the device in Remote Manager and click Actions > Open Console, or log into the EX15 local command line as a user with full Admin access rights.
Depending on your device configuration, you may be presented with an Access selection menu. Type admin to access the Admin CLI.
- Use the show surelink openvpn client name command to show the Surelink status of a specific OpenVPN client, for example:
> show surelink openvpn client test_client1 OpenVPN Client Test Last Response Status -------------- -------------------- ------------- ------------------ test_client1 194.43.79.74 (Ping) 29 seconds Passed test_client1 194.43.79.75 (Ping) 5 seconds Passed >
- Type exit to exit the Admin CLI.
Depending on your device configuration, you may be presented with an Access selection menu. Type quit to disconnect from the device.
PDF
