Asynchronous Message Reference¶
The following are asynchronous messages with defined status codes, corresponding to key events observed by the local device. See message* for more information on the “message” RPC response.
The message format is as follows:
<message>
<status type="int">0x1234</status>
<description type="string">Human-readable description</description>
<severity type="int">0x1</severity>
...other parameters as appropriate...
</message>
The “status” parameter gives a specific 16-bit integer status code corresponding to what the message is about, i.e. status 0x0000 corresponds to “local device has finished initialization”. Depending on the status code, other parameters may be included, i.e. a MAC address might be included if the status is about another device on the network. Separating parameters in this fashion is done because it is inconvenient to parse the description string of the message for useful information.
Local Device Status¶
The following messages correspond to the status of the local device.
Status Codes
Code | Name | Severity | Description |
---|---|---|---|
0x0000 | Init Complete | Warning (1) | Device initialization, including importing of Python modules and instantiation of objects, has completed. |
0x0001 | Joined Network | Warning (1) | Device has detected that its XBee radio is joined to a ZigBee network. |
As of 1.5.0: Added parameter discovery_status (see Discovery Status Codes below). If local device discovery is complete | a call to get_device_information will return the fully discovered information for gateway. If incomplete | wait for a message* with status Discovery Complete before calling get_device_information.” | |
0x0002 | Left Network | Warning (1) | Device has detected that its XBee radio has left a ZigBee network (previously was joined and now is not joined). |
0x0003 | Time Synchronized | Warning (1) | Device has synchronized its time with some time source. |
0x0004 | Modem Status | Debug (0) | As of 1.4.0: This message indicates a change in the ZigBee state; for example, when a device has joined or left a network. Will include modem_status parameter that gives the new XBee status. (See Modem Status Codes below and XBee SE Manual for more details on modem status messages). |
Modem Status Codes (for Modem Status message)
ID | Status |
---|---|
0x0 | Hardware reset |
0x1 | Watchdog timer reset |
0x2 | Joined network (routers and end devices) |
0x3 | Disassociated |
0x6 | Coordinator started |
0x7 | Network security key was updated |
0x10 | Key establishment complete |
0x80 | Stack error |
Examples
<message>
<status type="int">0x0</status>
<description type="string">Initialization complete, starting main loop</description>
<severity type="int">0x1</severity>
</message>
<message>
<status type="int">0x1</status>
<description type="string">Local device detected that it is joined to a ZigBee network</description>
<severity type="int">0x1</severity>
<discovery_status type="int">0x0</discovery_status>
</message>
<message>
<status type="int">0x2</status>
<description type="string">Local device detected that it has left a ZigBee network</description>
<severity type="int">0x1</severity>
</message>
<message>
<status type="int">0x3</status>
<description type="string">Synchronization with NTP time server successful</description>
<severity type="int">0x1</severity>
</message>
Remote Device Status¶
The following messages correspond to the status of other devices on the network, as observed by the local device. See Device Activity for more details on how device activity is determined.
Status Codes
Code | Name | Severity | Description |
---|---|---|---|
0x0100 | Device Registered | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: Device address/link key pair has been registered with the XBee radio. |
0x0101 | Device Unregistered | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: Device address/link key pair has been unregistered from the XBee radio. |
0x0102 | Known Device Active | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: A device which was previously known by the local device has been detected on the network and appears to be active. As of 1.5.0: Added parameter discovery_status (see Discovery Status Codes below). If discovery is complete, a call to get_device_information will return the fully discovered information for the device. If incomplete, wait for a message* with status Discovery Complete before calling get_device_information. |
0x0103 | Unknown Device Active | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: A device which was previously unknown by the local device has been detected on the network and appears to be active. As of 1.5.0: Added parameter discovery_status (see Discovery Status Codes below). If discovery is complete, a call to get_device_information will return the fully discovered information for the device. If incomplete, wait for a message* with status Discovery Complete before calling get_device_information. |
0x0104 | Device Inactive | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: A device which previously appeared to be active now appears to be inactive or unresponsive. |
0x0105 | Known Device Announce | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: A ZDO Device Announce message has been received from a device previously known by the local device. |
0x0106 | Unknown Device Announce | Warning (1) | Before 1.3.3: Message generated without status parameter. As of 1.3.3: A ZDO Device Announce message has been received from a device previously unknown by the local device. |
0x0107 | Device Discovery Complete | Warning (1) | As of 1.5.0: Device automatic discovery is complete. Will include discovery_status parameter that gives the status of service discovery (in this case either complete(1) or complete with errors(2), see Discovery Status Codes below). The discovery process happens after a device joins the network, the gateway joins a network, the gateway restarts, or if the RPC command refresh_device_information is sent with the parameter ‘full_refresh’ set to True. A call to get_device_information will return the fully discovered information for the device. |
0x0109 | Join Notification | Debug (0) | As of 1.4.0: Remote device tries to join the network. This message is only generated when the gateway is a coordinator. Will include join_status parameter that gives the type of ZigBee join. (See Join Notification Status Codes below and XBee SE Manual for more details on join status messages). |
0x010A | Device Authenticated | Debug (0) | As of 1.4.0: Remote device successfully completes key establishment. This message is only generated when the gateway is a coordinator. (See XBee SE Manual for more details on device authenticated messages). |
Additional Parameters
Parameter | Type | Description |
---|---|---|
addr_extended | MAC | 64-bit extended address of the remote device. |
addr_short* | MAC | 16-bit network address of the remote device. Included only for ‘Known Device Announce’ and ‘Unknown Device Announce’ messages. |
join_status* | int | As of 1.4.0: Enumerated status value for devices trying to join gateway (See Join Notification Status Codes below). Included only for ‘Join Notification’ messages. |
discovery_status* | int | As of 1.5.0: Enumerated status value for automatic service discovery of devices on the network (See Discovery Status Codes below). Included only for ‘Joined Network’, ‘Known Device Active’, ‘Unknown Device Active’, and ‘Device Discovery Complete’ messages. |
Join Notification Status Codes
ID | Status |
---|---|
0x0 | Standard security secured rejoin |
0x1 | Standard security unsecured join |
0x2 | Device left |
0x3 | Standard security unsecured rejoin |
0x4 | High security secured rejoin |
0x5 | High security unsecured join |
0x7 | High security unsecured rejoin |
Discovery Status Codes
ID | Status |
---|---|
0x0 | Discovery Incomplete |
0x1 | Discovery Complete |
0x2 | Discovery Complete with Errors |
Examples
<message>
<status type="int">0x100</status>
<description type="string">ZDO_Device_Manager - Device 11:22:33:44:55:66:77:88 registered with XBee</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
</message>
<message>
<status type="int">0x101</status>
<description type="string">ZDO_Device_Manager - Device 11:22:33:44:55:66:77:88 unregistered from XBee</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
</message>
<message>
<status type="int">0x102</status>
<description type="string">ZDO_Device_Manager - Device 11:22:33:44:55:66:77:88 detected and marked as active</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
<discovery_status type="int">0x0</discovery_status>
</message>
<message>
<status type="int">0x103</status>
<description type="string">ZDO_Device_Manager - New Device 11:22:33:44:55:66:77:88 detected and marked as active</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
<discovery_status type="int">0x0</discovery_status>
</message>
<message>
<status type="int">0x104</status>
<description type="string">ZDO_Device_Manager - Device 11:22:33:44:55:66:77:88 marked as inactive because of transmission failures</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
</message>
<message>
<status type="int">0x105</status>
<description type="string">ZDO_Device_Manager - Received device announce message from known device 11:22:33:44:55:66:77:88 (NWK: 1234)</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
<addr_short type="MAC">1234</addr_short>
</message>
<message>
<status type="int">0x106</status>
<description type="string">ZDO_Device_Manager - Received device announce message from known device 11:22:33:44:55:66:77:88 (NWK: 1234)</description>
<severity type="int">0x1</severity>
<addr_extended type="MAC">11:22:33:44:55:66:77:88</addr_extended>
<addr_short type="MAC">1234</addr_short>
</message>
ZigBee Conversation Status¶
The following messages correspond to
Status Codes
Code | Name | Severity | Description |
---|---|---|---|
0x0200 | Conversation General Error | Warning (1) | Before 1.4.0: Message generated without status parameter. As of 1.4.0: General error occurred when handling a response from remote device. |
0x0201 | Conversation TX Status Error | Warning (1) | Before 1.4.0: Message generated without status parameter. As of 1.4.0: Transmission error when sending to remote device. (See ZigBee Transmission Status Codes below and XBee SE Manual for more details on TX status messages). |
0x0202 | Conversation Timeout Error | Warning (1) | Before 1.4.0: Message generated without status parameter. As of 1.4.0: Timeout occurred when waiting for response from remote device. Timeout duration can be set using the registry setting Conversation.default_timeout. (See Registry Settings). |
ZigBee Transmission Status Codes (for Conversation TX Status Error message)
ID | Status |
---|---|
0x00 | Success |
0x02 | CCA Failure |
0x18 | No Buffers |
0x21 | Network Ack Failure |
0x22 | Not Joined to Network |
0x24 | Address Not Found |
0x25 | Route Not Found |
0x26 | Relay of Broadcast Not Heard |
0x2B | Invalid Binding Table Index |
0x2C | Invalid Endpoint |
0x32 | Resource Error |
0x74 | Data Payload Too Large |
0xBB | Key Not Authorized |
Examples
<message>
<status type="int">0x200</status>
<description type="string"></description>
<severity type="int">0x1</severity>
</message>
<message>
<status type="int">0x201</status>
<description type="string"></description>
<severity type="int">0x1</severity>
</message>
<message>
<status type="int">0x202</status>
<description type="string"></description>
<severity type="int">0x1</severity>
</message>