Module pinout
The module has an LGA pad structure based on 400 pads. See the following diagram for the general layout, which shows the top view of the module pinouts.
The following table provides the pinout of the ConnectCore 6 module.
Additional timing and electrical information can be found in either the NXP i.MX6 processor datasheet (www.nxp.com) or the Dialog DA9063 product datasheet (www.dialog-semiconductor.com).
The microprocessor used on this module, like all CMOS devices, can be driven into a latch-up condition if any I/O pin is driven outside of its associated power rail. Care must be taken to:
- Never drive an I/O pin beyond its positive rail or below ground.
- Never drive an I/O pin from an external power source during the power-on or reset sequences.
- Never hot-swap the module or interrupt its ground connection to external circuitry.
Latch-up is a condition that can cause excessive current draw and result in excessive heating of the microprocessor or its power supplies. This excessive heating can permanently damage the microprocessor and/or its supporting components.
|
LGA pad |
Pad name |
Multiplexing |
Power group |
Comments |
|
A5 |
CSI0_MCLK |
ALT0: IPU1_CSI0_HSYNC ALT1: ALT2: ALT3: CCM_CLKO1 ALT4: ALT5: GPIO5_IO19 ALT6: ALT7: ARM_TRACE_CTL |
NVCC_CSI |
|
|
A6 |
CSI0_DAT11 |
ALT0: IPU1_CSI0_DATA11 ALT1: AUD3_RXFS ALT2: ECSPI2_SS0 ALT3: UART1_RX_DATA ALT4: ALT5: GPIO5_IO29 ALT6: ALT7: ARM_TRACE08 |
NVCC_CSI |
Connected to the on-module MCA microcontroller. |
|
A7 |
CSI0_DAT17 |
ALT0: IPU1_CSI0_DATA17 ALT1: EIM_DATA13 ALT2: ALT3: UART4_CTS_B ALT4: ALT5: GPIO6_IO03 ALT6: ALT7: ARM_TRACE14 |
NVCC_CSI |
|
|
A8 |
GND |
- |
- |
|
|
A9 |
HDMI_D0_N |
- |
HDMI_VPH |
|
|
A10 |
GND |
- |
- |
|
|
A11 |
CSI_CLK0_P |
- |
NVCC_MIPI |
|
|
A12 |
GND |
- |
- |
|
|
A13 |
CSI_D1_N |
- |
NVCC_MIPI |
|
|
A14 |
PCIE_RX_N |
- |
PCIE_VPH |
|
|
A15 |
PCIE_TX_N |
- |
PCIE_VPH |
|
|
A16 |
CLK2_P |
- |
VDD_HIGH_CAP |
|
|
A17 |
GND |
- |
- |
|
|
A18 |
CLK1_P |
- |
VDD_HIGH_CAP |
|
|
A19 |
MLB_DP |
- |
VDD_HIGH_CAP |
|
|
A20 |
MLB_DN |
- |
VDD_HIGH_CAP |
|
|
B4 |
LVDS0_TX2_P |
- |
NVCC_LVDS_2P5 |
|
|
B5 |
GND |
- |
- |
|
|
B6 |
CSI0_DAT14 |
ALT0: IPU1_CSI0_DATA14 ALT1: EIM_DATA10 ALT2: ALT3: UART5_TX_DATA ALT4: ALT5: GPIO6_IO00 ALT6: ALT7: ARM_TRACE11 |
NVCC_CSI |
|
|
B7 |
CSI0_DAT4 |
ALT0: IPU1_CSI0_DATA04 ALT1: EIM_DATA02 ALT2: ECSPI1_SCLK ALT3: KEY_COL5 ALT4: AUD3_TXC ALT5: GPIO5_IO22 ALT6: ALT7: ARM_TRACE01 |
NVCC_CSI |
|
|
B8 |
HDMI_D1_N |
- |
HDMI_VPH |
|
|
B9 |
HDMI_D0_P |
- |
HDMI_VPH |
|
|
B10 |
DSI_D0_P |
- |
NVCC_MIPI |
|
|
B11 |
CSI_CLK0_N |
- |
NVCC_MIPI |
|
|
B12 |
CSI_D2_N |
- |
NVCC_MIPI |
|
|
B13 |
CSI_D1_P |
- |
NVCC_MIPI |
|
|
B14 |
PCIE_RX_P |
- |
PCIE_VPH |
|
|
B15 |
PCIE_TX_P |
- |
PCIE_VPH |
|
|
B16 |
CLK2_N |
- |
VDD_HIGH_CAP |
|
|
B17 |
GND |
- |
- |
|
|
B18 |
CLK1_N |
- |
VDD_HIGH_CAP |
|
|
B19 |
GND |
- |
- |
|
|
B20 |
GND |
- |
- |
|
|
B21 |
SD3_CLK/ BT_UART_RTS |
ALT0: SD3_CLK ALT1: UART2_RTS_B ALT2: FLEXCAN1_RX ALT3: ALT4: ALT5: GPIO7_IO03 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
The signal is only available externally on modules that do not have Bluetooth populated. |
|
C3 |
KEY_COL3 |
ALT0: ECSPI1_SS3 ALT1: ENET_CRS ALT2: HDMI_TX_DDC_SCL ALT3: KEY_COL3 ALT4: I2C2_SCL ALT5: GPIO4_IO12 ALT6: SPDIF_IN ALT7: |
NVCC_GPIO (VGEN_3V3) |
Connected to MCA processor and PMIC. Not recommended as main I2C port. 4,7K pull-up on module. |
|
C4 |
LVDS0_TX2_N |
- |
NVCC_LVDS_2P5 |
|
|
C5 |
CSI0_DAT6 |
ALT0: IPU1_CSI0_DATA06 ALT1: EIM_DATA04 ALT2: ECSPI1_MISO ALT3: KEY_COL6 ALT4: AUD3_TXFS ALT5: GPIO5_IO24 ALT6: ALT7: ARM_TRACE03 |
NVCC_CSI |
|
|
C6 |
CSI0_DAT13 |
ALT0: IPU1_CSI0_DATA13 ALT1: EIM_DATA09 ALT2: ALT3: UART4_RX_DATA ALT4: ALT5: GPIO5_IO31 ALT6: ALT7: ARM_TRACE10 |
NVCC_CSI |
|
|
C7 |
CSI0_DAT5 |
ALT0: IPU1_CSI0_DATA05 ALT1: EIM_DATA03 ALT2: ECSPI1_MOSI ALT3: KEY_ROW5 ALT4: AUD3_TXD ALT5: GPIO5_IO23 ALT6: ALT7: ARM_TRACE02 |
NVCC_CSI |
|
|
C8 |
HDMI_D1_P |
- |
HDMI_VPH |
|
|
C9 |
GND |
- |
- |
|
|
C10 |
DSI_D0_N |
- |
NVCC_MIPI |
|
|
C11 |
GND |
- |
- |
|
|
C12 |
CSI_D2_P |
- |
NVCC_MIPI |
|
|
C13 |
GND |
- |
- |
|
|
C14 |
GND |
- |
- |
|
|
C15 |
GND |
- |
- |
|
|
C16 |
USB_H1_DN |
- |
VDD_USB_CAP |
|
|
C17 |
TAMPER |
- |
VDD_SNVS_IN |
|
|
C18 |
Reserved |
- |
- |
|
|
C19 |
MLB_SP |
- |
VDD_HIGH_CAP |
|
|
C20 |
MLB_SN |
- |
VDD_HIGH_CAP |
|
|
C21 |
SD3_DAT7 |
ALT0: SD3_DATA7 ALT1: UART1_TX_DATA ALT2: ALT3: ALT4: ALT5: GPIO6_IO17 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
C22 |
SD3_DAT4/ BT_UART_RXD |
ALT0: SD3_DATA4 ALT1: UART2_RX_DATA ALT2: ALT3: ALT4: ALT5: GPIO7_IO01 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
The signal is only available externally on modules that do not have Bluetooth populated. |
|
D2 |
KEY_ROW4 |
ALT0: FLEXCAN2_RX ALT1: IPU1_SISG5 ALT2: USB_OTG_PWR ALT3: KEY_ROW4 ALT4: UART5_CTS_B ALT5: GPIO4_IO15 ALT6: ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
D3 |
KEY_ROW1 |
ALT0: ECSPI1_SS0 ALT1: ENET_COL ALT2: AUD5_RXD ALT3: KEY_ROW1 ALT4: UART5_RX_DATA ALT5: GPIO4_IO09 ALT6: SD2_VSELECT ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
D4 |
GND |
- |
- |
|
|
D5 |
CSI0_DAT9 |
ALT0: IPU1_CSI0_DATA09 ALT1: EIM_DATA07 ALT2: ECSPI2_MOSI ALT3: KEY_ROW7 ALT4: I2C1_SCL ALT5: GPIO5_IO27 ALT6: ALT7: ARM_TRACE06 |
NVCC_CSI |
Connected to the on-module MCA microcontroller. |
|
D6 |
CSI0_DAT8 |
ALT0: IPU1_CSI0_DATA08 ALT1: EIM_DATA06 ALT2: ECSPI2_SCLK ALT3: KEY_COL7 ALT4: I2C1_SDA ALT5: GPIO5_IO26 ALT6: ALT7: ARM_TRACE05 |
NVCC_CSI |
Connected to the on-module MCA microcontroller. |
|
D7 |
HDMI_DDCCEC |
- |
HDMI_VPH |
|
|
D8 |
GND |
- |
- |
|
|
D9 |
DSI_D1_P |
- |
NVCC_MIPI |
|
|
D10 |
GND |
- |
- |
|
|
D11 |
CSI_D3_P |
- |
NVCC_MIPI |
|
|
D12 |
Reserved |
- |
- |
|
|
D13 |
#BT_DISABLE |
- |
WLAN/BT_3V3 |
|
|
D14 |
JTAG_TDI |
- |
NVCC_JTAG (VGEN_3V3) |
|
|
D15 |
#JTAG_TRST |
- |
NVCC_JTAG (VGEN_3V3) |
|
|
D16 |
USB_H1_DP |
- |
VDD_USB_CAP |
|
|
D17 |
TEST_MODE |
- |
VDD_SNVS_IN |
10K pull-down on module. |
|
D18 |
ON/OFF |
- |
VDD_SNVS_IN |
Input power on/off line of the module (active-low). |
|
D19 |
SATA_TX_N |
- |
SATA_VPH |
|
|
D20 |
GND |
- |
- |
|
|
D21 |
SD3_DAT1 |
ALT0: SD3_DATA1 ALT1: UART1_RTS_B ALT2: FLEXCAN2_RX ALT3: ALT4: ALT5: GPIO7_IO05 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
D22 |
SD3_RST |
ALT0: SD3_RESET ALT1: UART3_RTS_B ALT2: ALT3: ALT4: ALT5: GPIO7_IO08 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
D23 |
SD3_DAT5/ BT_UART_TXD |
ALT0: SD3_DATA5 ALT1: UART2_TX_DATA ALT2: ALT3: ALT4: ALT5: GPIO7_IO00 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
The signal is only available externally on modules that do not have Bluetooth populated. |
|
E1 |
LVDS1_CLK_N |
- |
NVCC_LVDS_2P5 |
|
|
E2 |
KEY_ROW0 |
ALT0: ECSPI1_MOSI ALT1: ENET_TX_DATA3 ALT2: AUD5_TXD ALT3: KEY_ROW0 ALT4: UART4_RX_DATA ALT5: GPIO4_IO07 ALT6: DCIC2_OUT ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
E3 |
KEY_COL1 |
ALT0: ECSPI1_MISO ALT1: ENET_MDIO ALT2: AUD5_TXFS ALT3: KEY_COL1 ALT4: UART5_TX_DATA ALT5: GPIO4_IO08 ALT6: SD1_VSELECT ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
E4 |
LVDS0_TX1_P |
- |
NVCC_LVDS_2P5 |
|
|
E5 |
CSI0_DATA_EN |
ALT0: IPU1_CSI0_DATA_EN ALT1: EIM_DATA00 ALT2: ALT3: ALT4: ALT5: GPIO5_IO20 ALT6: ALT7: ARM_TRACE_CLK |
NVCC_CSI |
|
|
E6 |
CSI0_DAT15 |
ALT0: IPU1_CSI0_DATA15 ALT1: EIM_DATA11 ALT2: ALT3: UART5_RX_DATA ALT4: ALT5: GPIO6_IO01 ALT6: ALT7: ARM_TRACE12 |
NVCC_CSI |
|
|
E7 |
GND |
- |
- |
|
|
E8 |
HDMI_CLK_N |
- |
HDMI_VPH |
|
|
E9 |
DSI_D1_N |
- |
NVCC_MIPI |
|
|
E10 |
DSI_CLK0_N |
- |
NVCC_MIPI |
|
|
E11 |
CSI_D3_N |
- |
NVCC_MIPI |
|
|
E12 |
Reserved |
- |
- |
|
|
E13 |
Reserved |
- |
- |
|
|
E14 |
JTAG_TDO |
- |
NVCC_JTAG (VGEN_3V3) |
|
|
E15 |
Reserved |
- |
- |
|
|
E16 |
GND |
- |
- |
|
|
E17 |
BOOT_MODE0 |
- |
VDD_SNVS_IN |
10K pull-down on module. |
|
E18 |
#POR |
- |
VDD_SNVS_IN |
This is an active low, bi-directional line which is also driven by the PMIC in an open-drain output configuration. It can be used as either input or output:
|
|
E19 |
SATA_TX_P |
- |
SATA_VPH |
|
| E20 |
VGEN_3V3 |
- |
|
|
|
E21 |
SD3_DAT6 |
ALT0: SD3_DATA6 ALT1: UART1_RX_DATA ALT2: ALT3: ALT4: ALT5: GPIO6_IO18 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
E22 |
NANDF_CLE/ BT_WAKE |
ALT0: NAND_CLE ALT1: IPU2_SISG4 ALT2: ALT3: ALT4: ALT5: GPIO6_IO07 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
The signal is only available externally on modules that do not have Bluetooth populated. |
|
E23 |
SD3_CMD/ BT_UART_CTS |
ALT0: SD3_CMD ALT1: UART2_CTS_B ALT2: FLEXCAN1_TX ALT3: ALT4: ALT5: GPIO7_IO02 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
The signal is only available externally on modules that do not have Bluetooth populated. |
|
E24 |
SD3_DAT2 |
ALT0: SD3_DATA2 ALT1: ALT2: ALT3: ALT4: ALT5: GPIO7_IO06 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
F1 |
LVDS1_CLK_P |
- |
NVCC_LVDS_2P5 |
|
|
F2 |
KEY_ROW3 |
ALT0: ALT1: ASRC_EXT_CLK ALT2: HDMI_TX_DDC_SDA ALT3: KEY_ROW3 ALT4: I2C2_SDA ALT5: GPIO4_IO13 ALT6: SD1_VSELECT ALT7: |
NVCC_GPIO (VGEN_3V3) |
Connected to MCA processor and PMIC. Not recommended as main I2C port. 4,7K pull-up on module. |
|
F3 |
GPIO_8 |
ALT0: ESAI_TX5_RX0 ALT1: XTALOSC_REF_CLK_32K ALT2: EPIT2_OUT ALT3: FLEXCAN1_RX ALT4: UART2_RX_DATA ALT5: GPIO1_IO08 ALT6: SPDIF_SR_CLK ALT7: USB_OTG_PWR_CTL_WAKE ALT8: I2C4_SDA |
NVCC_GPIO (VGEN_3V3) |
|
|
F4 |
LVDS0_TX1_N |
- |
NVCC_LVDS_2P5 |
|
|
F5 |
GND |
- |
- |
|
|
F6 |
CSI0_DAT18 |
ALT0: IPU1_CSI0_DATA18 ALT1: EIM_DATA14 ALT2: ALT3: UART5_RTS_B ALT4: ALT5: GPIO6_IO04 ALT6: ALT7: ARM_TRACE15 |
NVCC_CSI |
|
|
F7 |
HDMI_D2_N |
- |
HDMI_VPH |
|
|
F8 |
HDMI_CLK_P |
- |
HDMI_VPH |
|
|
F9 |
GND |
- |
- |
|
|
F10 |
DSI_CLK0_P |
- |
NVCC_MIPI |
|
|
F11 |
GND |
- |
- |
|
|
F12 |
GND |
- |
- |
|
|
F13 |
JTAG_TCK |
- |
NVCC_JTAG (VGEN_3V3) |
|
|
F14 |
JTAG_TMS |
- |
NVCC_JTAG (VGEN_3V3) |
|
|
F15 |
BOOT_MODE1 |
- |
VDD_SNVS_IN |
10K pull-up to VDD_SNVS_IN on module. |
|
F16 |
USB_H1_VBUS |
- |
- |
|
|
F17 |
MLB_CP |
- |
- |
|
|
F18 |
MLB_CN |
- |
- |
|
|
F19 |
GND |
- |
- |
|
|
F20 |
SD3_DAT0 |
ALT0: SD3_DATA0 ALT1: UART1_CTS_B ALT2: FLEXCAN2_TX ALT3: ALT4: ALT5: GPIO7_IO04 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
F21 |
NANDF_CS0 |
ALT0: NAND_CE0_B ALT1: ALT2: ALT3: ALT4: ALT5: GPIO6_IO11 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
F22 |
#NANDF_WP |
ALT0: NAND_WP_B ALT1: IPU2_SISG5 ALT2: ALT3: ALT4: ALT5: GPIO6_IO09 ALT6: ALT7: ALT9: I2C4_SCL |
NVCC_NANDF (VGEN_3V3) |
|
|
F23 |
NANDF_CS3 |
ALT0: NAND_CE3_B ALT1: IPU1_SISG1 ALT2: ESAI_TX1 ALT3: EIM_ADDR26 ALT4: ALT5: GPIO6_IO16 ALT6: IPU2_SISG1 ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
F24 |
SD3_DAT3 |
ALT0: SD3_DATA3 ALT1: UART3_CTS_B ALT2: ALT3: ALT4: ALT5: GPIO7_IO07 ALT6: ALT7: |
NVCC_SD3 (VGEN_3V3) |
|
|
G1 |
GND |
- |
- |
|
|
G2 |
GPIO_0 |
ALT0: CCM_CLKO1 ALT1: ALT2: KEY_COL5 ALT3: ASRC_EXT_CLK ALT4: EPIT1_OUT ALT5: GPIO1_IO00 ALT6: USB_H1_PWR ALT7: SNVS_VIO_5 |
NVCC_GPIO (VGEN_3V3) |
|
|
G3 |
GPIO_2 |
ALT0: ESAI_TX_FS ALT1: ALT2: KEY_ROW6 ALT3: ALT4: ALT5: GPIO1_IO02 ALT6: SD2_WP ALT7: MLB_DATA |
NVCC_GPIO (VGEN_3V3) |
|
|
G4 |
GND |
- |
- |
|
|
G5 |
CSI0_PIXCLK |
ALT0: IPU1_CSI0_PIXCLK ALT1: ALT2: ALT3: ALT4: ALT5: GPIO5_IO18 ALT6: ALT7: ARM_EVENTO |
NVCC_CSI |
|
|
G6 |
CSI0_DAT19 |
ALT0: IPU1_CSI0_DATA19 ALT1: EIM_DATA15 ALT2: ALT3: UART5_CTS_B ALT4: ALT5: GPIO6_IO05 ALT6: ALT7: |
NVCC_CSI |
|
|
G7 |
HDMI_D2_P |
- |
HDMI_VPH |
|
|
G8 |
GND |
- |
- |
|
|
G9 |
HDMI_HPD |
- |
HDMI_VPH |
|
|
G10 |
GND |
- |
- |
|
|
G11 |
CSI_D0_P |
- |
NVCC_MIPI |
|
|
G12 |
CSI_D0_N |
- |
NVCC_MIPI |
|
|
G13 |
JTAG_MOD |
- |
NVCC_JTAG (VGEN_3V3) |
|
|
G14 |
USB_OTG_VBUS |
- |
USB_OTG_VBUS |
|
|
G15 |
#USB_OTG_CHD |
- |
VDD_USB_CAP |
|
|
G16 |
USB_OTG_DN |
- |
VDD_USB_CAP |
|
|
G17 |
USB_OTG_DP |
- |
VDD_USB_CAP |
|
|
G18 |
GND |
- |
- |
|
|
G19 |
SATA_RX_N |
- |
SATA_VPH |
|
| G20 |
VGEN_3V3 |
- |
- |
|
|
G21 |
NANDF_D2 |
ALT0: NAND_DATA02 ALT1: SD1_DATA6 ALT2: ALT3: ALT4: ALT5: GPIO2_IO02 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
G22 |
NANDF_D6 |
ALT0: NAND_DATA06 ALT1: SD2_DATA6 ALT2: ALT3: ALT4: ALT5: GPIO2_IO06 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
G23 |
NANDF_D3 |
ALT0: NAND_DATA03 ALT1: SD1_DATA7 ALT2: ALT3: ALT4: ALT5: GPIO2_IO03 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
G24 |
NANDF_ALE |
ALT0: NAND_ALE ALT1: SD4_RESET ALT2: ALT3: ALT4: ALT5: GPIO6_IO08 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
H1 |
LVDS1_TX0_N |
- |
NVCC_LVDS_2P5 |
|
|
H2 |
KEY_ROW2 |
ALT0: ECSPI1_SS2 ALT1: ENET_TX_DATA2 ALT2: FLEXCAN1_RX ALT3: KEY_ROW2 ALT4: SD2_VSELECT ALT5: GPIO4_IO11 ALT6: HDMI_TX_CEC_LINE ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
H3 |
GPIO_9 |
ALT0: ESAI_RX_FS ALT1: WDOG1_B ALT2: KEY_COL6 ALT3: CCM_REF_EN_B ALT4: PWM1_OUT ALT5: GPIO1_IO09 ALT6: SD1_WP ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
H4 |
LVDS0_TX0_P |
- |
NVCC_LVDS_2P5 |
|
|
H5 |
GND |
- |
- |
|
|
H6 |
CSI0_DAT16 |
ALT0: IPU1_CSI0_DATA16 ALT1: EIM_DATA12 ALT2: ALT3: UART4_RTS_B ALT4: ALT5: GPIO6_IO02 ALT6: ALT7: ARM_TRACE13 |
NVCC_CSI |
|
|
H19 |
SATA_RX_P |
- |
SATA_VPH |
|
|
H20 |
GND |
- |
- |
|
|
H21 |
NANDF_CS1/ #MCA_INT |
ALT0: NAND_CE1_B ALT1: SD4_VSELECT ALT2: SD3_VSELECT ALT3: ALT4: ALT5: GPIO6_IO14 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
Connected to MCA processor. |
|
H22 |
NANDF_D1 |
ALT0: NAND_DATA01 ALT1: SD1_DATA5 ALT2: ALT3: ALT4: ALT5: GPIO2_IO01 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
H23 |
NANDF_D7 |
ALT0: NAND_DATA07 ALT1: SD2_DATA7 ALT2: ALT3: ALT4: ALT5: GPIO2_IO07 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
H24 |
NANDF_CS2 |
ALT0: NAND_CE2_B ALT1: IPU1_SISG0 ALT2: ESAI_TX0 ALT3: EIM_CRE ALT4: CCM_CLKO2 ALT5: GPIO6_IO15 ALT6: IPU2_SISG0 ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
J1 |
LVDS1_TX0_P |
- |
NVCC_LVDS_2P5 |
|
|
J2 |
KEY_COL0 |
ALT0: ECSPI1_SCLK ALT1: ENET_RX_DATA3 ALT2: AUD5_TXC ALT3: KEY_COL0 ALT4: UART4_TX_DATA ALT5: GPIO4_IO06 ALT6: DCIC1_OUT ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
J3 |
GPIO_6 |
ALT0: ESAI_TX_CLK ALT1: ALT2: I2C3_SDA ALT3: ALT4: ALT5: GPIO1_IO06 ALT6: SD2_LCTL ALT7: MLB_SIG |
NVCC_GPIO (VGEN_3V3) |
|
|
J4 |
LVDS0_TX0_N |
- |
NVCC_LVDS_2P5 |
|
|
J5 |
CSI0_VSYNC |
ALT0: IPU1_CSI0_VSYNC ALT1: EIM_DATA01 ALT2: ALT3: ALT4: ALT5: GPIO5_IO21 ALT6: ALT7: ARM_TRACE00 |
NVCC_CSI |
|
| J20 |
VGEN_3V3 |
- | - | |
|
J21 |
SD1_DAT2 |
ALT0: SD1_DATA2 ALT1: ECSPI5_SS1 ALT2: GPT_COMPARE2 ALT3: PWM2_OUT ALT4: WDOG1_B ALT5: GPIO1_IO19 ALT6: WDOG1_RESET_B_DEB ALT7: |
NVCC_SD1 (VGEN_3V3) |
The signal is only available externally on modules that do not have Wi-Fi populated. |
|
J22 |
SD1_DAT1 |
ALT0: SD1_DATA1 ALT1: ECSPI5_SS0 ALT2: PWM3_OUT ALT3: GPT_CAPTURE2 ALT4: ALT5: GPIO1_IO17 ALT6: ALT7: |
NVCC_SD1 (VGEN_3V3) |
The signal is only available externally on modules that do not have Wi-Fi populated. |
|
J23 |
SD1_CMD |
ALT0: SD1_CMD ALT1: ECSPI5_MOSI ALT2: PWM4_OUT ALT3: GPT_COMPARE1 ALT4: ALT5: GPIO1_IO18 ALT6: ALT7: |
NVCC_SD1 (VGEN_3V3) |
The signal is only available externally on modules that do not have Wi-Fi populated. |
|
J24 |
NANDF_D0 |
ALT0: NAND_DATA00 ALT1: SD1_DATA4 ALT2: ALT3: ALT4: ALT5: GPIO2_IO00 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
K1 |
GND |
- |
- |
|
|
K2 |
KEY_COL2 |
ALT0: ECSPI1_SS1 ALT1: ENET_RX_DATA2 ALT2: FLEXCAN1_TX ALT3: KEY_COL2 ALT4: ENET_MDC ALT5: GPIO4_IO10 ALT6: USB_H1_PWR_CTL_WAKE ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
K3 |
GPIO_1 |
ALT0: ESAI_RX_CLK ALT1: WDOG2_B ALT2: KEY_ROW5 ALT3: USB_OTG_ID ALT4: PWM2_OUT ALT5: GPIO1_IO01 ALT6: SD1_CD_B ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
K4 |
GND |
- |
- |
|
|
K5 |
CSI0_DAT10 |
ALT0: IPU1_CSI0_DATA10 ALT1: AUD3_RXC ALT2: ECSPI2_MISO ALT3: UART1_TX_DATA ALT4: ALT5: GPIO5_IO28 ALT6: ALT7: ARM_TRACE07 |
NVCC_CSI |
Connected to the on-module MCA microcontroller. |
|
K20 |
VGEN_3V3 |
- | - | |
|
K21 |
SD2_DAT1 |
ALT0: SD2_DATA1 ALT1: ECSPI5_SS0 ALT2: EIM_CS2 ALT3: AUD4_TXFS ALT4: KEY_COL7 ALT5: GPIO1_IO14 ALT6: ALT7: |
NVCC_SD2 (VGEN_3V3) |
|
|
K22 |
SD2_CLK |
ALT0: SD2_CLK ALT1: ECSPI5_SCLK ALT2: KEY_COL5 ALT3: AUD4_RXFS ALT4: ALT5: GPIO1_IO10 ALT6: ALT7: |
NVCC_SD2 (VGEN_3V3) |
|
|
K23 |
SD2_DAT3 |
ALT0: SD2_DATA3 ALT1: ECSPI5_SS3 ALT2: KEY_COL6 ALT3: AUD4_TXC ALT4: ALT5: GPIO1_IO12 ALT6: ALT7: |
NVCC_SD2 (VGEN_3V3) |
|
|
K24 |
NANDF_D4 |
ALT0: NAND_DATA04 ALT1: SD2_DATA4 ALT2: ALT3: ALT4: ALT5: GPIO2_IO04 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
L1 |
LVDS1_TX1_P |
- |
NVCC_LVDS_2P5 |
|
|
L2 |
KEY_COL4 |
ALT0: FLEXCAN2_TX ALT1: IPU1_SISG4 ALT2: USB_OTG_OC ALT3: KEY_COL4 ALT4: UART5_RTS_B ALT5: GPIO4_IO14 ALT6: ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
L3 |
GPIO_4 |
ALT0: ESAI_TX_HF_CLK ALT1: ALT2: KEY_COL7 ALT3: ALT4: ALT5: GPIO1_IO04 ALT6: SD2_CD_B ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
L4 |
LVDS0_CLK_P |
- |
NVCC_LVDS_2P5 |
|
|
L5 |
CSI0_DAT12 |
ALT0: IPU1_CSI0_DATA12 ALT1: EIM_DATA08 ALT2: ALT3: UART4_TX_DATA ALT4: ALT5: GPIO5_IO30 ALT6: ALT7: ARM_TRACE09 |
NVCC_CSI |
|
|
L20 |
SD1_DAT3 |
ALT0: SD1_DATA3 ALT1: ECSPI5_SS2 ALT2: GPT_COMPARE3 ALT3: PWM1_OUT ALT4: WDOG2_B ALT5: GPIO1_IO21 ALT6: WDOG2_RESET_B_DEB ALT7: |
NVCC_SD1 (VGEN_3V3) |
The signal is only available externally on modules that do not have Wi-Fi populated. |
|
L21 |
SD1_CLK |
ALT0: SD1_CLK ALT1: ECSPI5_SCLK ALT2: ALT3: GPT_CLKIN ALT4: ALT5: GPIO1_IO20 ALT6: ALT7: |
NVCC_SD1 (VGEN_3V3) |
The signal is only available externally on modules that do not have Wi-Fi populated. |
|
L22 |
GND |
- |
- |
|
|
L23 |
MCA_SWD_CLK |
ALT0: - ALT1: PTA0 ALT2: - ALT3: TMP0_CH5 ALT4: - ALT5: - ALT6: - ALT7: SWD_CLK |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
L24 |
NANDF_D5 |
ALT0: NAND_DATA05 ALT1: SD2_DATA5 ALT2: ALT3: ALT4: ALT5: GPIO2_IO05 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
M1 |
LVDS1_TX1_N |
- |
NVCC_LVDS_2P5 |
|
|
M2 |
GPIO_19 |
ALT0: KEY_COL5 ALT1: ENET_1588_EVENT0_OUT ALT2: SPDIF_OUT ALT3: CCM_CLKO1 ALT4: ECSPI1_RDY ALT5: GPIO4_IO05 ALT6: ENET_TX_ER ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
M3 |
GPIO_16 |
ALT0: ESAI_TX3_RX2 ALT1: ENET_1588_EVENT2_IN ALT2: ENET_REF_CLK ALT3: SD1_LCTL ALT4: SPDIF_IN ALT5: GPIO7_IO11 ALT6: I2C3_SDA ALT7: JTAG_DE_B |
NVCC_GPIO (VGEN_3V3) |
|
|
M4 |
LVDS0_CLK_N |
- |
NVCC_LVDS_2P5 |
|
|
M5 |
CSI0_DAT7 |
ALT0: IPU1_CSI0_DATA07 ALT1: EIM_DATA05 ALT2: ECSPI1_SS0 ALT3: KEY_ROW6 ALT4: AUD3_RXD ALT5: GPIO5_IO25 ALT6: ALT7: ARM_TRACE04 |
NVCC_CSI |
|
|
M20 |
SD2_CMD |
ALT0: SD2_CMD ALT1: ECSPI5_MOSI ALT2: KEY_ROW5 ALT3: AUD4_RXC ALT4: ALT5: GPIO1_IO11 ALT6: ALT7: |
NVCC_SD2 (VGEN_3V3) |
|
|
M21 |
MCA_IO12 |
ALT0: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
M22 |
LDO3_MCA |
- | - |
|
|
M23 |
MCA_SWD_DIO |
ALT0: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
M24 |
NANDF_RB0 |
ALT0: NAND_READY ALT1: IPU2_DI0_PIN01 ALT2: ALT3: ALT4: ALT5: GPIO6_IO10 ALT6: ALT7: |
NVCC_NANDF (VGEN_3V3) |
|
|
N1 |
GND |
- |
- |
|
|
N2 |
GPIO_18 |
ALT0: ESAI_TX1 ALT1: ENET_RX_CLK ALT2: SD3_VSELECT ALT3: SDMA_EXT_EVENT1 ALT4: ASRC_EXT_CLK ALT5: GPIO7_IO13 ALT6: SNVS_VIO_5_CTL ALT7: |
NVCC_GPIO (VGEN_3V3) |
|
|
N3 |
VCC_LICELL |
- | - | |
|
N4 |
GND |
- | - | |
| N5 |
VGEN_3V3 |
- | - | |
|
N20 |
MCA_IO/USB0_P |
ALT0: ADC0_SE1 |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
N21 |
MCA_IO13 |
ALT0: CMP0_IN0 |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
N22 |
MCA_IO7 |
ALT0: - ALT1: PTB16 ALT2: SPI1_MOSI ALT3: UART0_RX ALT4: TPM_CLKIN0 ALT5: SPI1_MISO ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
N23 |
#MCA_RESET |
ALT0: RESET_b ALT1: PTA20 ALT2: - ALT3: - ALT4: - ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
|
|
N24 |
SD1_DAT0 |
ALT0: SD1_DATA0 ALT1: ECSPI5_MISO ALT2: ALT3: GPT_CAPTURE1 ALT4: ALT5: GPIO1_IO16 ALT6: ALT7: |
NVCC_SD1 (VGEN_3V3) |
The signal is only available externally on modules that do not have Wi-Fi populated. |
|
P1 |
LVDS1_TX2_N |
- |
NVCC_LVDS_2P5 |
|
|
P2 |
ENET_CRS_DV |
ALT0: ENET_RX_EN ALT1: ESAI_TX_CLK ALT2: SPDIF_EXT_CLK ALT3: ALT4: ALT5: GPIO1_IO25 ALT6: ALT7: |
NVCC_ENET |
|
|
P3 |
GPIO_7 |
ALT0: ESAI_TX4_RX1 ALT1: ECSPI5_RDY ALT2: EPIT1_OUT ALT3: FLEXCAN1_TX ALT4: UART2_TX_DATA ALT5: GPIO1_IO07 ALT6: SPDIF_LOCK ALT7: USB_OTG_HOST_MODE ALT8: I2C4_SCL |
NVCC_GPIO (VGEN_3V3) |
|
|
P4 |
LVDS0_TX3_P |
- |
NVCC_LVDS_2P5 |
|
| P5 |
NVCC_CSI |
- |
NVCC_CSI |
|
|
P20 |
MCA_IO/USB0_N |
ALT0: ADC0_SE5a ALT1: PTE17 ALT2: SPI0_SCK ALT3: UART2_RX ALT4: TPM_CLKIN1 ALT5: - ALT6: LPTMR0_ALT3 ALT7: - |
LDO3_MCA |
Assuming NXP MKL14Z32VFT4 is populated.
Signal not used on the module.
|
|
P21 |
MCA_IO14 |
ALT0: ADC0_SE6a ALT1: PTE19 ALT2: SPI0_MISO ALT3: - ALT4: I2C0_SCL ALT5: SPI0_MOSI ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
P22 |
MCA_IO8 |
ALT0: - ALT1: PTB17 ALT2: SPI1_MISO ALT3: UART0_TX ALT4: TPM_CLKIN1 ALT5: SPI1_MOSI ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
P23 |
MCA_IO1 |
ALT0: ADC0_SE4a ALT1: PTE21 ALT2: - ALT3: TPM1_CH1 ALT4: UART0_RX ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
P24 |
SD2_DAT0 |
ALT0: SD2_DATA0 ALT1: ECSPI5_MISO ALT2: ALT3: AUD4_RXD ALT4: KEY_ROW7 ALT5: GPIO1_IO15 ALT6: DCIC2_OUT ALT7: |
NVCC_SD2 (VGEN_3V3) |
|
|
R1 |
LVDS1_TX2_P |
- |
NVCC_LVDS_2P5 |
|
|
R2 |
ENET_RX_ER |
ALT0: USB_OTG_ID ALT1: ENET_RX_ER ALT2: ESAI_RX_HF_CLK ALT3: SPDIF_IN ALT4: ENET_1588_EVENT2_OUT ALT5: GPIO1_IO24 ALT6: ALT7: |
NVCC_ENET |
|
|
R3 |
GPIO_5 |
ALT0: ESAI_TX2_RX3 ALT1: ALT2: KEY_ROW7 ALT3: CCM_CLKO1 ALT4: ALT5: GPIO1_IO05 ALT6: I2C3_SCL ALT7: ARM_EVENTI |
NVCC_GPIO (VGEN_3V3) |
|
|
R4 |
LVDS0_TX3_N |
- |
NVCC_LVDS_2P5 |
|
|
R5 |
NVCC_RGMII |
- |
NVCC_RGMII |
|
|
R20 |
MCA_IO19 |
ALT0: CMP0_IN1 ALT1: PTC7 ALT2: SPI0_MISO ALT3: - ALT4: - ALT5: SPI0_MOSI ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
R21 |
MCA_IO16 |
ALT0: - ALT1: PTD4/LLWU_P14 ALT2: SPI1_PCS0 ALT3: UART2_RX ALT4: TPM0_CH4 ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
R22 |
MCA_IO9 |
ALT0: ADC0_SE11 ALT1: PTC2 ALT2: I2C1_SDA ALT3: - ALT4: TPM0_CH1 ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
R23 |
MCA_IO2 |
ALT0: ADC0_SE8 ALT1: PTB0/LLWU_P5 ALT2: I2C0_SCL ALT3: TPM1_CH0 ALT4: - ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
R24 |
SD2_DAT2 |
ALT0: SD2_DATA2 ALT1: ECSPI5_SS1 ALT2: EIM_CS3 ALT3: AUD4_TXD ALT4: KEY_ROW6 ALT5: GPIO1_IO13 ALT6: ALT7: |
NVCC_SD2 (VGEN_3V3) |
|
|
T1 |
GND |
- |
- |
|
|
T2 |
GND |
- |
- |
|
|
T3 |
GPIO_3 |
ALT0: ESAI_RX_HF_CLK ALT1: ALT2: I2C3_SCL ALT3: XTALOSC_REF_CLK_24M ALT4: CCM_CLKO2 ALT5: GPIO1_IO03 ALT6: USB_H1_OC ALT7: MLB_CLK |
NVCC_GPIO (VGEN_3V3) |
|
|
T4 |
GND |
- |
- |
|
|
T5 |
GND |
- |
- |
|
|
T20 |
MCA_IO24 |
ALT0: XTAL0 ALT1: PTA19 ALT2: - ALT3: UART1_TX ALT4: TPM_CLKIN1 ALT5: - ALT6: LPTMR0_ALT1 ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
T21 |
MCA_IO22 |
ALT0: ADC0_SE6b ALT1: PTD5 ALT2: SPI1_SCK ALT3: UART2_TX ALT4: TPM0_CH5 ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
T22 |
MCA_IO10 |
ALT0: - ALT1: PTC3/LLWU_P7 ALT2: - ALT3: UART1_RX ALT4: TPM0_CH2 ALT5: CLKOUT ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
T23 |
MCA_IO0 |
ALT0: ADC0_SE0 ALT1: PTE20 ALT2: - ALT3: TPM1_CH0 ALT4: UART0_TX ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
T24 |
MCA_IO3 |
ALT0: ADC0_SE7b ALT1: PTD6/LLWU_P15 ALT2: SPI1_MOSI ALT3: UART0_RX ALT4: - ALT5: SPI1_MISO ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
U1 |
LVDS1_TX3_N |
- |
NVCC_LVDS_2P5 |
|
|
U2 |
ENET_TXD0 |
ALT0: ALT1: ENET_TX_DATA0 ALT2: ESAI_TX4_RX1 ALT3: ALT4: ALT5: GPIO1_IO30 ALT6: ALT7: |
NVCC_ENET |
|
|
U3 |
GND |
- |
- |
|
|
U4 |
RGMII_TXC |
ALT0: USB_H2_DATA ALT1: RGMII_TXC ALT2: SPDIF_EXT_CLK ALT3: ALT4: ALT5: GPIO6_IO19 ALT6: ALT7: XTALOSC_REF_CLK_24M |
NVCC_RGMII |
|
|
U5 |
RGMII_TD0 |
ALT0: HSI_TX_READY ALT1: RGMII_TD0 ALT2: ALT3: ALT4: ALT5: GPIO6_IO20 ALT6: ALT7: |
NVCC_RGMII |
|
|
U6 |
DISP0_DAT21 |
ALT0: IPU1_DISP0_DATA21 ALT1: IPU2_DISP0_DATA21 ALT2: ECSPI1_MOSI ALT3: AUD4_TXD ALT4: ALT5: GPIO5_IO15 ALT6: ALT7: |
NVCC_LCD |
|
|
U19 |
EIM_DA3 |
ALT0: EIM_DA03 ALT1: IPU1_DISP1_DATA06 ALT2: IPU2_CSI1_DATA06 ALT3: ALT4: ALT5: GPIO3_IO03 ALT6: ALT7: SRC_BOOT_CFG03 ALT8: EPDC BDR1 |
NVCC_EIM |
|
|
U20 |
EIM_DA0 |
ALT0: EIM_AD00 ALT1: IPU1_DISP1_DATA09 ALT2: IPU2_CSI1_DATA09 ALT3: ALT4: ALT5: GPIO3_IO00 ALT6: ALT7: SRC_BOOT_CFG00 ALT8: EPDC_SDCLK_N |
NVCC_EIM |
|
|
U21 |
EIM_LBA |
ALT0: EIM_LBA ALT1: IPU1_DI1_PIN17 ALT2: ECSPI2_SS1 ALT3: ALT4: ALT5: GPIO2_IO27 ALT6: ALT7: SRC_BOOT_CFG26 ALT8: EPDC_DATA04 |
NVCC_EIM |
|
|
U22 |
MCA_IO11 |
ALT0: - ALT1: PTC4/LLWU_P8 ALT2: SPI0_PCS0 ALT3: UART1_TX ALT4: TPM0_CH3 ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
U23 |
EIM_DA6 |
ALT0: EIM_AD06 ALT1: IPU1_DISP1_DATA03 ALT2: IPU2_CSI1_DATA03 ALT3: ALT4: ALT5: GPIO3_IO06 ALT6: ALT7: SRC_BOOT_CFG06 ALT8: EPDC_SDCE2 |
NVCC_EIM |
10K pull-up to NVCC_EIM on module. |
|
U24 |
MCA_IO4 |
ALT0: ADC0_SE14 ALT1: PTC0 ALT2: - ALT3: EXTRG_IN ALT4: - ALT5: CMP0_OUT ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
V1 |
LVDS1_TX3_P |
- |
NVCC_LVDS_2P5 |
|
|
V2 |
ENET_TXD1 |
ALT0: MLB_CLK ALT1: ENET_TX_DATA1 ALT2: ESAI_TX2_RX3 ALT3: ALT4: ENET_1588_EVENT0_IN ALT5: GPIO1_IO29 ALT6: ALT7: ALT9: I2C4_SDA |
NVCC_ENET |
|
|
V3 |
NVCC_ENET |
- |
NVCC_ENET |
|
|
V4 |
RGMII_RX_CTL |
ALT0: USB_H3_DATA ALT1: RGMII_RX_CTL ALT2: ALT3: ALT4: ALT5: GPIO6_IO24 ALT6: ALT7: |
NVCC_RGMII |
|
|
V5 |
RGMII_TD1 |
ALT0: HSI_RX_FLAG ALT1: RGMII_TD1 ALT2: ALT3: ALT4: ALT5: GPIO6_IO21 ALT6: ALT7: |
NVCC_RGMII |
|
|
V6 |
DISP0_DAT16 |
ALT0: IPU1_DISP0_DATA16 ALT1: IPU2_DISP0_DATA16 ALT2: ECSPI2_MOSI ALT3: AUD5_TXC ALT4: SDMA_EXT_EVENT0 ALT5: GPIO5_IO10 ALT6: ALT7: |
NVCC_LCD |
|
|
V7 |
DISP0_DAT22 |
ALT0: IPU1_DISP0_DATA22 ALT1: IPU2_DISP0_DATA22 ALT2: ECSPI1_MISO ALT3: AUD4_TXFS ALT4: ALT5: GPIO5_IO16 ALT6: ALT7: |
NVCC_LCD |
|
|
V8 |
DI0_PIN3 |
ALT0: IPU1_DI0_PIN03 ALT1: IPU2_DI0_PIN03 ALT2: AUD6_TXFS ALT3: ALT4: ALT5: GPIO4_IO19 ALT6: ALT7: |
NVCC_LCD |
|
|
V9 |
DI0_DISP_CLK |
ALT0: IPU1_DI0_DISP_CLK ALT1: IPU2_DI0_DISP_CLK ALT2: ALT3: ALT4: ALT5: GPIO4_IO16 ALT6: ALT7: |
NVCC_LCD |
|
|
V10 |
DI0_PIN15 |
ALT0: IPU1_DI0_PIN15 ALT1: IPU2_DI0_PIN15 ALT2: AUD6_TXC ALT3: ALT4: ALT5: GPIO4_IO17 ALT6: ALT7: |
NVCC_LCD |
|
| V11 | VSYS | - | - | |
|
V12 |
PMIC_GPIO11 |
- | - |
PMIC |
|
V13 |
PMIC_GPIO15 |
- | - |
PMIC |
|
V14 |
CHG_WAKE |
- | - |
PMIC |
|
V15 |
EIM_OE |
ALT0: EIM_OE ALT1: IPU1_DI1_PIN07 ALT2: ECSPI2_MISO ALT3: ALT4: ALT5: GPIO2_IO25 ALT6: ALT7: ALT8: EPDC_PWR_IRQ |
NVCC_EIM |
|
|
V16 |
EIM_EB1 |
ALT0: EIM_EB1 ALT1: IPU1_DISP1_DATA10 ALT2: IPU2_CSI1_DATA10 ALT3: ALT4: ALT5: GPIO2_IO29 ALT6: ALT7: SRC_BOOT_CFG28 ALT8: EPDC_SDSHR |
NVCC_EIM |
|
|
V17 |
EIM_D17 |
ALT0: EIM_DATA17 ALT1: ECSPI1_MISO ALT2: IPU1_DI0_PIN06 ALT3: IPU2_CSI1_PIXCLK ALT4: DCIC1_OUT ALT5: GPIO3_IO17 ALT6: I2C3_SCL ALT7: ALT8: EPDC_VCOM0 |
NVCC_EIM |
|
|
V18 |
EIM_DA11 |
ALT0: EIM_DA11 ALT1: IPU1_DI1_PIN02 ALT2: IPU2_CSI1_HSYNC ALT3: ALT4: ALT5: GPIO3_IO11 ALT6: ALT7: SRC_BOOT_CFG11 ALT8: EPDC_DATA03 |
NVCC_EIM |
10K pull-up to NVCC_EIM on module. |
|
V19 |
EIM_DA9 |
ALT0: EIM_DA9 ALT1: IPU1_DISP1_DATA00 ALT2: IPU2_CSI1_DATA00 ALT3: ALT4: ALT5: GPIO3_IO09 ALT6: ALT7: SRC_BOOT_CFG09 ALT8: EPDC_SDCE5 |
NVCC_EIM |
|
|
V20 |
EIM_DA13 |
ALT0: EIM_DA13 ALT1: IPU1_DI1_D0_CS ALT2: ALT3: ALT4: ALT5: GPIO3_IO13 ALT6: ALT7: SRC_BOOT_CFG13 ALT8: EPDC_DATA13 |
NVCC_EIM |
10K pull-down on module. |
|
V21 |
EIM_DA10 |
ALT0: EIM_DA10 ALT1: IPU1_DI1_PIN15 ALT2: IPU2_CSI1_DATA_EN ALT3: ALT4: ALT5: GPIO3_IO10 ALT6: ALT7: SRC_BOOT_CFG10 ALT8: EPDC_DATA01 |
NVCC_EIM |
|
|
V22 |
EIM_DA12 |
ALT0: EIM_DA12 ALT1: IPU1_DI1_PIN03 ALT2: IPU2_CSI1_VSYNC ALT3: ALT4: ALT5: GPIO3_IO12 ALT6: ALT7: SRC_BOOT_CFG12 ALT8: EPDC_DATA02 |
NVCC_EIM |
10K pull-up to NVCC_EIM on module. |
|
V23 |
GND |
- |
- |
|
|
V24 |
EIM_DA2 |
ALT0: EIM_DA02 ALT1: IPU1_DISP1_DATA07 ALT2: IPU2_CSI1_DATA07 ALT3: ALT4: ALT5: GPIO3_IO02 ALT6: ALT7: SRC_BOOT_CFG02 ALT8: EPDC_BDR0 |
NVCC_EIM |
|
|
W1 |
GND |
- |
- |
|
|
W2 |
GND |
- |
- |
|
|
W3 |
ENET_MDC |
ALT0: MLB_DATA ALT1: ENET_MDC ALT2: ESAI_TX5_RX0 ALT3: ALT4: ENET_1588_EVENT1_IN ALT5: GPIO1_IO31 ALT6: ALT7: |
NVCC_ENET |
|
|
W4 |
RGMII_TX_CTL |
ALT0: USB_H2_STROBE ALT1: RGMII_TX_CTL ALT2: ALT3: ALT4: ALT5: GPIO6_IO26 ALT6: ALT7: ENET_REF_CLK |
NVCC_RGMII |
|
|
W5 |
GND |
- |
- |
|
|
W6 |
DISP0_DAT20 |
ALT0: IPU1_DISP0_DATA20 ALT1: IPU2_DISP0_DATA20 ALT2: ECSPI1_SCLK ALT3: AUD4_TXC ALT4: ALT5: GPIO5_IO14 ALT6: ALT7: |
NVCC_LCD |
|
|
W7 |
DISP0_DAT15 |
ALT0: IPU1_DISP0_DATA15 ALT1: IPU2_DISP0_DATA15 ALT2: ECSPI1_SS1 ALT3: ECSPI2_SS1 ALT4: ALT5: GPIO5_IO09 ALT6: ALT7: |
NVCC_LCD |
|
|
W8 |
DISP0_DAT13 |
ALT0: IPU1_DISP0_DATA13 ALT1: IPU2_DISP0_DATA13 ALT2: ALT3: AUD5_RXFS ALT4: ALT5: GPIO5_IO07 ALT6: ALT7: |
NVCC_LCD |
|
|
W9 |
GND |
- |
- |
|
|
W10 |
DI0_PIN2 |
ALT0: IPU1_DI0_PIN02 ALT1: IPU2_DI0_PIN02 ALT2: AUD6_TXD ALT3: ALT4: ALT5: GPIO4_IO18 ALT6: ALT7: |
NVCC_LCD |
|
| W11 | VSYS | - | - | |
| W12 | VSYS | - | - | |
|
W13 |
PMIC_PWR_EN |
- | - |
PMIC |
|
W14 |
GND |
- | - | |
|
W15 |
EIM_RW |
ALT0: EIM_RW ALT1: IPU1_DI1_PIN08 ALT2: ECSPI2_SS0 ALT3: ALT4: ALT5: GPIO2_IO26 ALT6: ALT7: SRC_BOOT_CFG29 ALT8: EPDC_DATA07 |
NVCC_EIM |
|
|
W16 |
EIM_D29 |
ALT0: EIM_DATA29 ALT1: IPU1_DI1_PIN15 ALT2: ECSPI4_SS0 ALT3: ALT4: UART2_RTS_B ALT5: GPIO3_IO29 ALT6: IPU2_CSI1_VSYNC ALT7: IPU1_DI0_PIN14 ALT8: EPDC_PWR_WAKE |
NVCC_EIM |
|
|
W17 |
GND |
- |
- |
|
|
W18 |
EIM_A25 |
ALT0: EIM_ADDR25 ALT1: ECSPI4_SS1 ALT2: ECSPI2_RDY ALT3: IPU1_DI1_PIN12 ALT4: IPU1_DI0_D1_CS ALT5: GPIO5_IO02 ALT6: HDMI_TX_CEC_LINE ALT7: ALT8: EPDC_DATA15 |
NVCC_EIM |
|
|
W19 |
EIM_D20 |
ALT0: EIM_DATA20 ALT1: ECSPI4_SS0 ALT2: IPU1_DI0_PIN16 ALT3: IPU2_CSI1_DATA15 ALT4: UART1_RTS_B ALT5: GPIO3_IO20 ALT6: EPIT2_OUT ALT7: |
NVCC_EIM |
|
|
W20 |
EIM_D24 |
ALT0: EIM_DATA24 ALT1: ECSPI4_SS2 ALT2: UART3_TX_DATA ALT3: ECSPI1_SS2 ALT4: ECSPI2_SS2 ALT5: GPIO3_IO24 ALT6: AUD5_RXFS ALT7: UART1_DTR_B ALT8: EPDC_SDCE7 |
NVCC_EIM |
|
|
W21 |
EIM_DA14 |
ALT0: EIM_DA14 ALT1: IPU1_DI1_D1_CS ALT2: ALT3: ALT4: ALT5: GPIO3_IO14 ALT6: ALT7: SRC_BOOT_CFG14 ALT8: EPDC_DATA14 |
NVCC_EIM |
10K pull-up to NVCC_EIM on module. |
|
W22 |
EIM_DA8 |
ALT0: EIM_DA8 ALT1: IPU1_DISP1_DATA01 ALT2: IPU2_CSI1_DATA01 ALT3: ALT4: ALT5: GPIO3_IO08 ALT6: ALT7: SRC_BOOT_CFG08 ALT8: EPDC_SDCE4 |
NVCC_EIM |
|
|
W23 |
EIM_DA1 |
ALT0: EIM_DA1 ALT1: IPU1_DISP1_DATA08 ALT2: IPU2_CSI1_DATA08 ALT3: ALT4: ALT5: GPIO3_IO01 ALT6: ALT7: SRC_BOOT_CFG01 ALT8: EPDC_SDLE |
NVCC_EIM |
|
|
W24 |
EIM_DA4 |
ALT0: EIM_DA4 ALT1: IPU1_DISP1_DATA05 ALT2: IPU2_CSI1_DATA05 ALT3: ALT4: ALT5: GPIO3_IO04 ALT6: ALT7: SRC_BOOT_CFG04 ALT8: EPDC_SDCE0 |
NVCC_EIM |
10K pull-down on module. |
|
Y1 |
ENET_REF_CLK |
ALT0: ALT1: ENET_TX_CLK ALT2: ESAI_RX_FS ALT3: ALT4: ALT5: GPIO1_IO23 ALT6: SPDIF_SR_CLK ALT7: |
NVCC_ENET |
|
|
Y2 |
ENET_RXD0 |
ALT0: ALT1: ENET_RX_DATA0 ALT2: ESAI_TX_HF_CLK ALT3: SPDIF_OUT ALT4: ALT5: GPIO1_IO27 ALT6: ALT7: |
NVCC_ENET |
|
|
Y3 |
ENET_MDIO |
ALT0: ALT1: ENET_MDIO ALT2: ESAI_RX_CLK ALT3: ALT4: ENET_1588_EVENT1_OUT ALT5: GPIO1_IO22 ALT6: SPDIF_LOCK ALT7: |
NVCC_ENET |
|
|
Y4 |
GND |
- |
- |
|
|
Y5 |
RGMII_TD2 |
ALT0: HSI_RX_DATA ALT1: RGMII_TD2 ALT2: ALT3: ALT4: ALT5: GPIO6_IO22 ALT6: ALT7: |
NVCC_RGMII |
|
|
Y6 |
DISP0_DAT19 |
ALT0: IPU1_DISP0_DATA19 ALT1: IPU2_DISP0_DATA19 ALT2: ECSPI2_SCLK ALT3: AUD5_RXD ALT4: AUD4_RXC ALT5: GPIO5_IO13 ALT6: ALT7: EIM_CS3 |
NVCC_LCD |
|
|
Y7 |
DISP0_DAT11 |
ALT0: IPU1_DISP0_DATA11 ALT1: IPU2_DISP0_DATA11 ALT2: ALT3: ALT4: ALT5: GPIO5_IO05 ALT6: ALT7: |
NVCC_LCD |
|
|
Y8 |
DISP0_DAT10 |
ALT0: IPU1_DISP0_DATA10 ALT1: IPU2_DISP0_DATA10 ALT2: ALT3: ALT4: ALT5: GPIO4_IO31 ALT6: ALT7: |
NVCC_LCD |
|
|
Y9 |
NVCC_LCD |
- |
NVCC_LCD |
|
|
Y10 |
PMIC_GPIO14 |
- |
- |
|
|
Y11 |
GND |
- |
- |
|
|
Y12 |
GND |
- |
- |
|
| Y13 |
NVCC_EIM |
- |
NVCC_EIM |
|
|
Y14 |
EIM_EB0 |
ALT0: EIM_EB0 ALT1: IPU1_DISP1_DATA11 ALT2: IPU2_CSI1_DATA11 ALT3: ALT4: CCM_PMIC_READY ALT5: GPIO2_IO28 ALT6: ALT7: SRC_BOOT_CFG27 ALT8: EPDC_PWR_COM |
NVCC_EIM |
|
|
Y15 |
EIM_D30 |
ALT0: EIM_DATA30 ALT1: IPU1_DISP1_DATA21 ALT2: IPU1_DI0_PIN11 ALT3: IPU1_CSI0_DATA03 ALT4: UART3_CTS_B ALT5: GPIO3_IO30 ALT6: USB_H1_OC ALT7: ALT8: EPDC_SDOEZ |
NVCC_EIM |
|
|
Y16 |
EIM_D21 |
ALT0: EIM_DATA21 ALT1: ECSPI4_SCLK ALT2: IPU1_DI0_PIN17 ALT3: IPU2_CSI1_DATA11 ALT4: USB_OTG_OC ALT5: GPIO3_IO21 ALT6: I2C1_SCL ALT7: SPDIF_IN |
NVCC_EIM |
|
|
Y17 |
EIM_D19 |
ALT0: EIM_DATA19 ALT1: ECSPI1_SS1 ALT2: IPU1_DI0_PIN08 ALT3: IPU2_CSI1_DATA16 ALT4: UART1_CTS_B ALT5: GPIO3_IO19 ALT6: EPIT1_OUT ALT7: ALT8: EPDC_DATA12 |
NVCC_EIM |
|
|
Y18 |
EIM_D22 |
ALT0: EIM_DATA22 ALT1: ECSPI4_MISO ALT2: IPU1_DI0_PIN01 ALT3: IPU2_CSI1_DATA10 ALT4: USB_OTG_PWR ALT5: GPIO3_IO22 ALT6: SPDIF_OUT ALT7: ALT8: EPDC_SDCE6 |
NVCC_EIM |
|
|
Y19 |
GND |
- |
- |
|
|
Y20 |
EIM_DA15 |
ALT0: EIM_DA15 ALT1: IPU1_DI1_PIN01 ALT2: IPU1_DI1_PIN04 ALT3: ALT4: ALT5: GPIO3_IO15 ALT6: ALT7: SRC_BOOT_CFG15 ALT8: EPDC_DATA09 |
NVCC_EIM |
|
|
Y21 |
EIM_DA7 |
ALT0: EIM_DA7 ALT1: IPU1_DISP1_DATA02 ALT2: IPU2_CSI1_DATA02 ALT3: ALT4: ALT5: GPIO3_IO07 ALT6: ALT7: SRC_BOOT_CFG07 ALT8: EPDC_SDCE3 |
NVCC_EIM |
10K pull-down on module. |
|
Y22 |
MCA_IO27 |
ALT0: ADC0_SE2 ALT1: PTE18 ALT2: SPI0_MOSI ALT3: - ALT4: I2C0_SDA ALT5: SPI0_MISO ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
Y23 |
MCA_IO23 |
ALT0: CMP0_IN5/ADC0_SE4b ALT1: PTE29 ALT2: - ALT3: TPM0_CH2 ALT4: TPM_CLKIN0 ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
Y24 |
EIM_EB2 |
ALT0: EIM_EB2 ALT1: ECSPI1_SS0 ALT2: ALT3: IPU2_CSI1_DATA19 ALT4: HDMI_TX_DDC_SCL ALT5: GPIO2_IO30 ALT6: I2C2_SCL ALT7: SRC_BOOT_CFG30 ALT8: EPDC_DATA05 |
NVCC_EIM |
|
|
AA2 |
ENET_RXD1 |
ALT0: MLB_SIG ALT1: ENET_RX_DATA1 ALT2: ESAI_TX_FS ALT3: ALT4: ENET_1588_EVENT3_OUT ALT5: GPIO1_IO26 ALT6: ALT7: |
NVCC_ENET |
|
|
AA3 |
ENET_TX_EN |
ALT0: ALT1: ENET_TX_EN ALT2: ESAI_TX3_RX2 ALT3: ALT4: ALT5: GPIO1_IO28 ALT6: ALT7: ALT9: I2C4_SCL |
NVCC_ENET |
|
|
AA4 |
RGMII_RD0 |
ALT0: HSI_RX_READY ALT1: RGMII_RD0 ALT2: ALT3: ALT4: ALT5: GPIO6_IO25 ALT6: ALT7: |
NVCC_RGMII |
|
|
AA5 |
RGMII_TD3 |
ALT0: HSI_RX_WAKE ALT1: RGMII_TD3 ALT2: ALT3: ALT4: ALT5: GPIO6_IO23 ALT6: ALT7: |
NVCC_RGMII |
|
|
AA6 |
DISP0_DAT23 |
ALT0: IPU1_DISP0_DATA23 ALT1: IPU2_DISP0_DATA23 ALT2: ECSPI1_SS0 ALT3: AUD4_RXD ALT4: ALT5: GPIO5_IO17 ALT6: ALT7: |
NVCC_LCD |
|
|
AA7 |
DISP0_DAT12 |
ALT0: IPU1_DISP0_DATA12 ALT1: IPU2_DISP0_DATA12 ALT2: ALT3: ALT4: ALT5: GPIO5_IO06 ALT6: ALT7: |
NVCC_LCD |
|
|
AA8 |
DISP0_DAT8 |
ALT0: IPU1_DISP0_DATA08 ALT1: IPU2_DISP0_DATA08 ALT2: PWM1_OUT ALT3: WDOG1_B ALT4: ALT5: GPIO4_IO29 ALT6: ALT7: |
NVCC_LCD |
|
|
AA9 |
DISP0_DAT4 |
ALT0: IPU1_DISP0_DATA04 ALT1: IPU2_DISP0_DATA04 ALT2: ECSPI3_SS1 ALT3: ALT4: ALT5: GPIO4_IO25 ALT6: ALT7: |
NVCC_LCD |
|
|
AA10 |
VLDO6 |
- | - | |
|
AA11 |
VLDO7 |
- | - | |
|
AA12 |
VGEN_3V3 |
- | - | |
|
AA13 |
EIM_WAIT |
ALT0: EIM_WAIT ALT1: EIM_DTACK_B ALT2: ALT3: ALT4: ALT5: GPIO5_IO00 ALT6: ALT7: SRC_BOOT_CFG25 |
NVCC_EIM |
|
|
AA14 |
EIM_A23 |
ALT0: EIM_ADDR23 ALT1: IPU1_DISP1_DATA18 ALT2: IPU2_CSI1_DATA18 ALT3: IPU2_SISG3 ALT4: IPU1_SISG3 ALT5: GPIO6_IO06 ALT6: ALT7: SRC_BOOT_CFG23 ALT8: EPDC_GDOE |
NVCC_EIM |
|
|
AA15 |
EIM_D31 |
ALT0: EIM_DATA31 ALT1: IPU1_DISP1_DATA20 ALT2: IPU1_DI0_PIN12 ALT3: IPU1_CSI0_DATA02 ALT4: UART3_RTS_B ALT5: GPIO3_IO31 ALT6: USB_H1_PWR ALT7: ALT8: EPDC_SDCLK_P |
NVCC_EIM |
|
|
AA16 |
GND |
- |
- |
|
|
AA17 |
EIM_D25 |
ALT0: EIM_DATA25 ALT1: ECSPI4_SS3 ALT2: UART3_RX_DATA ALT3: ECSPI1_SS3 ALT4: ECSPI2_SS3 ALT5: GPIO3_IO25 ALT6: AUD5_RXC ALT7: UART1_DSR_B ALT8: EPDC_SDCE8 |
NVCC_EIM |
|
|
AA18 |
EIM_EB3 |
ALT0: EIM_EB3 ALT1: ECSPI4_RDY ALT2: UART3_RTS_B ALT3: UART1_RI_B ALT4: IPU2_CSI1_HSYNC ALT5: GPIO2_IO31 ALT6: IPU1_DI1_PIN03 ALT7: SRC_BOOT_CFG31 ALT8: EPDC_SDCE0 |
NVCC_EIM |
Make sure this line is not pulled-high during boot. |
|
AA19 |
EIM_DA5 |
ALT0: EIM_DA5 ALT1: IPU1_DISP1_DATA04 ALT2: IPU2_CSI1_DATA04 ALT3: ALT4: ALT5: GPIO3_IO05 ALT6: ALT7: SRC_BOOT_CFG05 ALT8: EPDC_SDCE1 |
NVCC_EIM |
10K pull-up to NVCC_EIM on module. |
|
AA20 |
MCA_IO21 |
ALT0: - ALT1: PTD7 ALT2: SPI1_MISO ALT3: UART0_TX ALT4: - ALT5: SPI1_MOSI ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
AA21 |
MCA_IO26 |
ALT0: - ALT1: PTA4 ALT2: I2C1_SDA ALT3: TPM0_CH1 ALT4: - ALT5: - ALT6: - ALT7: NMI_b |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
AA22 |
MCA_IO25 |
ALT0: - ALT1: PTA1 ALT2: UART0_RX ALT3: TPM2_CH0 ALT4: - ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
AA23 |
MCA_IO6/PMIC_GP_FB2 |
ALT0: - ALT1: PTA2 ALT2: UART0_TX ALT3: TPM2_CH1 ALT4: - ALT5: - ALT6: - ALT7: - |
LDO3_MCA |
Signal only available in variants carrying the MCA. |
|
AB3 |
RGMII_RD1 |
ALT0: HSI_TX_FLAG ALT1: RGMII_RD1 ALT2: ALT3: ALT4: ALT5: GPIO6_IO27 ALT6: ALT7: |
NVCC_RGMII |
|
|
AB4 |
GND |
- |
- |
|
|
AB5 |
DISP0_DAT17 |
ALT0: IPU1_DISP0_DATA17 ALT1: IPU2_DISP0_DATA17 ALT2: ECSPI2_MISO ALT3: AUD5_TXD ALT4: SDMA_EXT_EVENT1 ALT5: GPIO5_IO11 ALT6: ALT7: |
NVCC_LCD |
|
|
AB6 |
DISP0_DAT9 |
ALT0: IPU1_DISP0_DATA09 ALT1: IPU2_DISP0_DATA09 ALT2: PWM2_OUT ALT3: WDOG2_B ALT4: ALT5: GPIO4_IO30 ALT6: ALT7: |
NVCC_LCD |
|
|
AB7 |
DISP0_DAT6 |
ALT0: IPU1_DISP0_DATA06 ALT1: IPU2_DISP0_DATA06 ALT2: ECSPI3_SS3 ALT3: AUD6_RXC ALT4: ALT5: GPIO4_IO27 ALT6: ALT7: |
NVCC_LCD |
|
|
AB8 |
DISP0_DAT3 |
ALT0: IPU1_DISP0_DATA03 ALT1: IPU2_DISP0_DATA03 ALT2: ECSPI3_SS0 ALT3: ALT4: ALT5: GPIO4_IO24 ALT6: ALT7: |
NVCC_LCD |
|
|
AB9 |
PMIC_GPIO7 |
- | - |
PMIC line. |
|
AB10 |
GND |
- | - | |
|
AB11 |
Reserved |
- | - | |
|
AB12 |
EIM_BCLK |
ALT0: EIM_BCLK ALT1: IPU1_DI1_PIN16 ALT2: ALT3: ALT4: ALT5: GPIO6_IO31 ALT6: ALT7: ALT8: EPDC_SDCE9 |
NVCC_EIM |
|
|
AB13 |
EIM_CS0 |
ALT0: EIM_CS0 ALT1: IPU1_DI1_PIN05 ALT2: ECSPI2_SCLK ALT3: ALT4: ALT5: GPIO2_IO23 ALT6: ALT7: ALT8: EPDC_DATA06 |
NVCC_EIM |
|
|
AB14 |
PMIC_ADCIN1/ GPIO0 |
- |
- |
PMIC line. |
|
AB15 |
EIM_A18 |
ALT0: EIM_ADDR18 ALT1: IPU1_DISP1_DATA13 ALT2: IPU2_CSI1_DATA13 ALT3: ALT4: ALT5: GPIO2_IO20 ALT6: ALT7: SRC_BOOT_CFG18 ALT8: EPDC_PWR_CTRL0 |
NVCC_EIM |
Make sure this line is not pulled-high during boot. |
|
AB16 |
EIM_A20 |
ALT0: EIM_ADDR20 ALT1: IPU1_DISP1_DATA15 ALT2: IPU2_CSI1_DATA15 ALT3: ALT4: ALT5: GPIO2_IO18 ALT6: ALT7: SRC_BOOT_CFG20 ALT8: EPDC_PWR_CTRL2 |
NVCC_EIM |
Make sure this line is not pulled-high during boot. |
|
AB17 |
EIM_D28 |
ALT0: EIM_DATA28 ALT1: I2C1_SDA ALT2: ECSPI4_MOSI ALT3: IPU2_CSI1_DATA12 ALT4: UART2_CTS_B ALT5: GPIO3_IO28 ALT6: IPU1_EXT_TRIG ALT7: IPU1_DI0_PIN13 ALT8: EPDC_PWR_CTRL3 |
NVCC_EIM |
|
|
AB18 |
EIM_D18 |
ALT0: EIM_DATA18 ALT1: ECSPI1_MOSI ALT2: IPU1_DI0_PIN07 ALT3: IPU2_CSI1_DATA17 ALT4: IPU1_DI1_D0_CS ALT5: GPIO3_IO18 ALT6: I2C3_SDA ALT7: ALT8: EPDC_VCOM1 |
NVCC_EIM |
|
|
AB19 |
PMIC_PWR1_EN |
- | - | |
|
AB20 |
#PMIC_VDD_FAULT |
- | - | |
|
AB21 |
GND |
- | - | |
|
AB22 |
#PMIC_OFF |
- | - | |
|
AC4 |
RGMII_RD2 |
ALT0: HSI_TX_DATA ALT1: RGMII_RD2 ALT2: ALT3: ALT4: ALT5: GPIO6_IO28 ALT6: ALT7: |
NVCC_RGMII |
|
|
AC5 |
RGMII_RD3 |
ALT0: HSI_TX_WAKE ALT1: RGMII_RD3 ALT2: ALT3: ALT4: ALT5: GPIO6_IO29 ALT6: ALT7: |
NVCC_RGMII |
|
|
AC6 |
DISP0_DAT14 |
ALT0: IPU1_DISP0_DATA14 ALT1: IPU2_DISP0_DATA14 ALT2: ALT3: AUD5_RXC ALT4: ALT5: GPIO5_IO08 ALT6: ALT7: |
NVCC_LCD |
|
|
AC7 |
DISP0_DAT7 |
ALT0: IPU1_DISP0_DATA07 ALT1: IPU2_DISP0_DATA07 ALT2: ECSPI3_RDY ALT3: ALT4: ALT5: GPIO4_IO28 ALT6: ALT7: |
NVCC_LCD |
|
|
AC8 |
DISP0_DAT0 |
ALT0: IPU1_DISP0_DATA00 ALT1: IPU2_DISP0_DATA00 ALT2: ECSPI3_SCLK ALT3: ALT4: ALT5: GPIO4_IO21 ALT6: ALT7: |
NVCC_LCD |
|
|
AC9 |
DISP0_DAT1 |
ALT0: IPU1_DISP0_DATA01 ALT1: IPU2_DISP0_DATA01 ALT2: ECSPI3_MOSI ALT3: ALT4: ALT5: GPIO4_IO22 ALT6: ALT7: |
NVCC_LCD |
|
|
AC10 |
MCA_VREFH |
VREFH |
- |
A 100 nF capacitor connected to GND is placed close to this pin on ConnectCore 6 SOM. |
|
AC11 |
Reserved |
- | - | Output power rail. |
|
AC12 |
GND |
- | - | |
|
AC13 |
GND |
- | - | |
|
AC14 |
PMIC_ADCIN2/ GPIO1 |
- | - |
PMIC line. |
|
AC15 |
EIM_CS1 |
ALT0: EIM_CS1 ALT1: IPU1_DI1_PIN06 ALT2: ECSPI2_MOSI ALT3: ALT4: ALT5: GPIO2_IO24 ALT6: ALT7: ALT8: EPDC_DATA08 |
NVCC_EIM |
|
|
AC16 |
EIM_A21 |
ALT0: EIM_ADDR21 ALT1: IPU1_DISP1_DATA16 ALT2: IPU2_CSI1_DATA16 ALT3: ALT4: ALT5: GPIO2_IO17 ALT6: ALT7: SRC_BOOT_CFG21 ALT8: EPDC_GDCLK |
NVCC_EIM |
Make sure this line is not pulled-high during boot. |
|
AC17 |
EIM_A17 |
ALT0: EIM_ADDR17 ALT1: IPU1_DISP1_DATA12 ALT2: IPU2_CSI1_DATA12 ALT3: ALT4: ALT5: GPIO2_IO21 ALT6: ALT7: SRC_BOOT_CFG17 ALT8: EPDC_PWR_STAT |
NVCC_EIM |
|
|
AC18 |
GND |
- |
- |
|
|
AC19 |
EIM_A22 |
ALT0: EIM_ADDR22 ALT1: IPU1_DISP1_DATA17 ALT2: IPU2_CSI1_DATA17 ALT3: ALT4: ALT5: GPIO2_IO16 ALT6: ALT7: SRC_BOOT_CFG22 ALT8: EPDC_GDSP |
NVCC_EIM |
|
|
AC20 |
EIM_D23 |
ALT0: EIM_DATA23 ALT1: IPU1_DI0_D0_CS ALT2: UART3_CTS_B ALT3: UART1_DCD_B ALT4: IPU2_CSI1_DATA_EN ALT5: GPIO3_IO23 ALT6: IPU1_DI1_PIN02 ALT7: IPU1_DI1_PIN14 ALT8: EPDC_DATA11 |
NVCC_EIM |
|
|
AC21 |
MCA_IO28 |
ALT0: - ALT1: PTE25 ALT2: - ALT3: TPM0_CH1 ALT4: - ALT5: I2C0_SDA ALT6: - ALT7: - |
LDO3_MCA |
Not used on the module. For K10 and K20 processors, this pin is VBAT. The ConnectCore 6 SOM has an 0R resistor on this pin for connecting this signal to LDO3_MCA. By default, the resistor is not populated and MCA_IO28 is available on module pad. 1x 100nF + 1x1µF capacitors connected to GND are placed close to this pin on the ConnectCore 6 SOM. |
|
AD5 |
RGMII_RXC |
ALT0: USB_H3_STROBE ALT1: RGMII_RXC ALT2: ALT3: ALT4: ALT5: GPIO6_IO30 ALT6: ALT7: |
NVCC_RGMII |
|
|
AD6 |
DISP0_DAT18 |
ALT0: IPU1_DISP0_DATA18 ALT1: IPU2_DISP0_DATA18 ALT2: ECSPI2_SS0 ALT3: AUD5_TXFS ALT4: AUD4_RXFS ALT5: GPIO5_IO12 ALT6: ALT7: EIM_CS2 |
NVCC_LCD |
|
|
AD7 |
DISP0_DAT5 |
ALT0: IPU1_DISP0_DATA05 ALT1: IPU2_DISP0_DATA05 ALT2: ECSPI3_SS2 ALT3: AUD6_RXFS ALT4: ALT5: GPIO4_IO26 ALT6: ALT7: |
NVCC_LCD |
|
|
AD8 |
DI0_PIN4 |
ALT0: IPU1_DI0_PIN04 ALT1: IPU2_DI0_PIN04 ALT2: AUD6_RXD ALT3: SD1_WP ALT4: ALT5: GPIO4_IO20 ALT6: ALT7: |
NVCC_LCD |
|
|
AD9 |
DISP0_DAT2 |
ALT0: IPU1_DISP0_DATA02 ALT1: IPU2_DISP0_DATA02 ALT2: ECSPI3_MISO ALT3: ALT4: ALT5: GPIO4_IO23 ALT6: ALT7: |
NVCC_LCD |
|
|
AD10 |
VLDO4 |
- | - | |
|
AD11 |
VLDO8 |
- | - | |
|
AD12 |
PMIC_GP_FB3 |
- | - |
PMIC |
|
AD13 |
PMIC_GP_FB1/ GPIO13 |
- | - |
PMIC |
|
AD14 |
PMIC_ADCIN3/ GPIO2 |
- | - |
PMIC |
|
AD15 |
EIM_A16 |
ALT0: EIM_ADDR16 ALT1: IPU1_DI1_DISP_CLK ALT2: IPU2_CSI1_PIXCLK ALT3: ALT4: ALT5: GPIO2_IO22 ALT6: ALT7: SRC_BOOT_CFG16 ALT8: EPDC_DATA00 |
NVCC_EIM |
|
|
AD16 |
EIM_A19 |
ALT0: EIM_ADDR19 ALT1: IPU1_DISP1_DATA14 ALT2: IPU2_CSI1_DATA14 ALT3: ALT4: ALT5: GPIO2_IO19 ALT6: ALT7: SRC_BOOT_CFG19 ALT8: EPDC_PWR_CTRL1 |
NVCC_EIM |
|
|
AD17 |
EIM_A24 |
ALT0: EIM_ADDR24 ALT1: IPU1_DISP1_DATA19 ALT2: IPU2_CSI1_DATA19 ALT3: IPU2_SISG2 ALT4: IPU1_SISG2 ALT5: GPIO5_IO04 ALT6: ALT7: SRC_BOOT_CFG24 ALT8: EPDC_GDRL |
NVCC_EIM |
|
|
AD18 |
EIM_D27 |
ALT0: EIM_DATA27 ALT1: IPU1_DI1_PIN13 ALT2: IPU1_CSI0_DATA00 ALT3: IPU2_CSI1_DATA13 ALT4: UART2_RX_DATA ALT5: GPIO3_IO27 ALT6: IPU1_SISG3 ALT7: IPU1_DISP1_DATA23 ALT8: EPDC_SDOE |
NVCC_EIM |
|
|
AD19 |
EIM_D26 |
ALT0: EIM_DATA26 ALT1: IPU1_DI1_PIN11 ALT2: IPU1_CSI0_DATA01 ALT3: IPU2_CSI1_DATA14 ALT4: UART2_TX_DATA ALT5: GPIO3_IO26 ALT6: IPU1_SISG2 ALT7: IPU1_DISP1_DATA22 ALT8: EPDC_SDOED |
NVCC_EIM |
|
|
AD20 |
EIM_D16 |
ALT0: EIM_DATA16 ALT1: ECSPI1_SCLK ALT2: IPU1_DI0_PIN05 ALT3: IPU2_CSI1_DATA18 ALT4: HDMI_TX_DDC_SDA ALT5: GPIO3_IO16 ALT6: I2C2_SDA ALT7: ALT8: EPDC_DATA10 |
NVCC_EIM |
Note Electrical and timing characteristics of the processor (i.MX6 DualLite/Dual/Quad), PMIC (DA9063), and MCA (MKL14Z32VFT4) can be found in the corresponding datasheets, which are publicly available from the manufacturer.
PDF
